Search:

Thanks for the help !
I found the problem being the little screw that clamps the encoder to the
motor shaft broke allowing the motor to turn without the encoder.
I marked the encoder when I...

??????????????????
Thanks!

tried putting in a different setting than the one I normally use with no luck ,
air supply is the same one to the machine at 100psi.
Still think it maybe the brake or encoder.
Anyone have a...

Hi
I have a HRT210 brush type 4th axis on a VF0, had not used the 4th axis in a while and installed it the other day and kept getting a servo overload alarm and it seemed like the 4th axis would...

Had the same problem on the same model machine and it was the low voltage power supply it would act up more in the cold weather before it completly went out.

Thanks Geof!
You guy's are the the best!

Hi
I have a 2001 Haas VFO and I am getting a lot of coolant in the way oil overflow tank, in 25 running hours it may fill this tank up with 90% coolant.
Any ideas were to start looking, cover...

got the fan kit in from Haas, now both fans work, I will see if I get the alarm again.
Brendan

Thanks Joe!
ordered the fan kit from HFO $78 Haas wants the old fans back?
Should the fans run all the time the machine is on?
is this considered spindle fans on the led in the board on the left...

Hi
I have a 2000 VFO that I got alarm 101 and 123 whilst running some parts.
If I reset the machine it will take around 20 minutes then do it again.
Should the fans on the vector drive work all...

I had the same problem on a 2000 VFO
Ended up being the air pressure drop after the air dryer on the compressor would work hard for along time it would begin to freeze reducing air flow to the...

Thanks for the great answer Greg!

Hi
If you have macos,rotation and scaling can you just add the probe or is more required?
Thanks!
Brendan

power supply # is made by Fortron model # SPI 200-G
Thanks!

Anyone know where to get a replacement low voltage power supply for a VF0.
The current one is made by Fortron but I can not find the same part new any where?
Thanks!
Brendan

Who supports Milltronics in Sydney Australia?
Thanks!
Brendan

Ended up replacing the main power board and all is good, I have the old board to see if we can repair it as a spare.
Thanks for all the help!

I ohmed the the little part what ever we want to call them(yellow dime sized discs there is 5 or 6 of them with 2 legs on each right below the .5 amp fuses) and one had zero resistance (connected...

I ohmed one of the thyristors and 1 was a dead short across he 2 legs,
This is the one where I think the fuse blows first,
Were do I get a replacement at?
Is there some kind of value thyristor to...

The overvoltage fuses are on the power supply board in the back pannel on the machine they have an LED that light up when they blow.

The voltage between the leg is equal when measuring between any...

I will try ohming the transformer.
There are 3 overvoltage fuses if I remove the one on the left and replace the other 2 and turn the disconnect on the fuses are OK, but when I repalce the left one...

After I turn on the main disconnect on the back of the machine the fuses blow.

Hi
While running my machine it started to kick an alarm and the servos stopped and the control flickered then shut down.
Thanks to the power company I measured the voltage coming in and the outer...

Hi
Thinking of changing from Valcool 790 to Blaser swisslube for our Haas VMC, due to bacteria and avaliablity .

any reasons not to change before we purchase?
Thanks!

?????????????

When I turn it on cold it seem to work, it I shut down after starting it will not restart for 15 minutes,checked for loose terminals.

When it will not power up you do not get the first beep upon...

It has not done it since I guess it did not like the cold front only a high of 65
here yesterday, I don't like it when it is that cold also.
But it sounds like the computer power supply.
thanks...

Hi
I have a problem with my VF0 2000 model.
Upon start up you will not hear the beep on the control like normal, just see the LED in the bottom corner of the screen that stays blank and will not...