Search:

Yes I have a book of disk. Not sure which one to use. Or how to use it exactly.

Nope no disk left in. I can get to the main screen and move in manual. Also I can review the program. But I can't get the machine to calibrate or run a program.

When I power up my machine I can not get it to calibrate and I am geting this alarm. "Integrator Parameter File Could Not Be Read From Disk. The File Allocation Table Is Corrupt.

Powered the machine up this morning to try and get a fault number for you and it stopped giving an alarm. If it does it again I will get the fault code to you. It seems like it only does it when I...

Yes there is. It says something like F00000

I am having a similar problem on my Hurco BMC2416 98model. When I power on the controler and servos about 15 secounds go by and I get a spindle fault alarm. I reset the servos and spindle and the...

Screen started to jump around again this morning and I did blokes test. Looks like I have a bad membrane. Where can I order a new one of these? I called Hurco and they said they could only sell me a...

Ok started the machine up at 6:00am this morning when it was cool, made sure everything was clean and connected well. I started it up and the machine ran fine, so I was never able to run the blokes...

Notice I am not touching any of the buttons on the machine.2012 06 29 15 33 55 491 - YouTube

All fans are running fine. I checked power to the machine and its perfect.

I am having problems with my Hurco bmc2416 after I get it turned on and warmed up it keeps asking for z calibration. And after I press cycle start the screen starts to spaz out. I had a similar...

When I turn on my machine and ask it to calibrate the cycle start light will not light up and machine will not calibrate. I can get the atc to calibrate in the atc menu, but not the axis. I can also...

Ok, I crawled up to the top of the machine. Took the cover off, and took an air hose to the proxy switch. It seems to be working fine now. This is the same switch that has given me trouble before. ...

My hurco bmc2416 is picking the wrong tools during a tool change and is putting them in a different pocket then listed on the atc map. I checked the prox switch it seems to be working fine. I saw...

When i take out the front of the cotroller board from the control panal it seems to stop. agggghghghghghgh. so frusterating!!!!!!!!

Ok i have checked all the grounds and all the conectors. still not fixed. Any ideas??

Narrowed it down to cin/j2 conector. Maybe lose or dirty.

Ok, I took the front off the controler. After i did that it worked fine when i bolted it back up it started to act up again only wanting to stay in input mode. I took it back apart and wiggeled it...

Fixed it. prox switch was out of adjustment

Took back cover off control box. and sprayed some contact cleaner in it. seemed to help a little bit.

I have a hurco bmc 2416 with an ultimax controll. After i power up the machine it automaticly jumps to the input menu. when i press auto it goes to the auto screen for a few secounds then goes back...

Could it be a prox switch on the tool change magazine? The magazine will calebrate but when i move the magazine manualy in moves four pods either direction then needs to be calebrated again. But...

Nope problem still not fixed. spindle will stop and go to tool change hight. then nothing.

Ok i will check this out first thing tomorow. The spindle goes up to tool change hight and the spindle orients and the controller says tool change in progress then about thirty secounds go by and...

When i am running a program on my hurco bmc 2416. Sometimes the tool pod will not come down. Not allowing a full tool change. Then the machine faults out. Could the selinoid be going bad?

Bloke your the best, that fixed it. Still got a little bit of a bump when changing direction. But i think that is normal. Thanks for helping a yank out.

I adjusted the y axis paramater. The x axis is smooth as silk. How do I reduce proportional gain? My master program is "mill system version 2.15 oct 26 1999"

Ok bloke changed the servos still have the same problem. Then i went into service mode. Then servo tuning and incresed the gain form one to two. And the viberation got much worse. How do i turn the...

I tried to balance out the servo this morning in the service mode. This did not work. I am now gonna try and switch the x axis servo with the y axis servo and see if i have the same problem.

Not really a whinning noise when i move the table in y axis. Just the normal sound. The servo amplifiers have no led screen. Just green lights. I will try to post a video tommrow. The table just...