So dig this. FadalCNC.com has done business under this name for 18 years and now Fadal wants to sue us if we don't reverse 18 years of marketing in 30 days. Crazy. Regardless, we have moved to our...
Type: Posts; User: ASIGuy
So dig this. FadalCNC.com has done business under this name for 18 years and now Fadal wants to sue us if we don't reverse 18 years of marketing in 30 days. Crazy. Regardless, we have moved to our...
That's how I'd do it, then do an amp clamp test running about 150ipm the length of table travel and measure the current going out to the motors. Make sure it' 3 amp or so not under load.
Hello Jason, first, the fan is just dirty likely. You can try to clean it or buy a new one (their fairly cheap). $48.00. Here's a link: https://www.fadalcnc.com/index.php/ele-0124.html.
The...
So you know, this feature was designed to fight thermal growth of the ballcrews over the days work. When the systems is running properly, I think it is a great way to eliminate thermal growth. ...
Warrenb, setting up and testing your RT is quite easy. You only need a rigid tapping test tool (SVT-0077- $75 in stock), put in a collet holder and run a short rigid tapping program while you have...
Sir,
The copper lines are there to keep the lines tight to the castings so you have no issue with holes rubbing into them, or the nylon if you used it. Stay with copper. It's cheap and keeps...
If all else fails, power down and remove the PC Board in slot #5 after you do a check on your battery. Reseat the extended memory if you have any, and reseat the software module. Put it back in and...
Sir, there is an RS232 Troubleshooting guide I can send you which includes a test for your communications board. If you get your board back and your communications is still not working, contact me...
Sir, I have a hard time believing the inverter can cause a boot up problem honestly. Hook up your inverter if not already and power up the machine. Press the green power button. If the machine...
Sir, you will need to replace the battery on your CPU board. It is in slot #5 of your control rack. Desolder the battery on the board and solder the new one back in. You will lose everything again...
Very likely you have an issue with the ballscrew type in the parameters as mentioned before. If you are still unable to get the accuracy right, look at the thrust bearings and ballscrew. You might...
Sir, we carry all the metering units (injectors) for any Fadal in the field however I have never heard of this size. If you can tell me where it is from on your Fadal, I can likely get you a...
Ginner. It sounds like you have a CPU board and/or software module bad. If you have checked your 5VDC supplied by the low voltage power supply on the top of your electronics cabinet and all is good...
Sir,
Are you looking for the parameters for the machine? Let me know and I will try to help as I can.
FadalCNC Tech Support
Hello Gary. If you are speaking of a typical CNC88 control, the ELE-0189 (CRT Style) is the installed monitor. You would replace it with an LCD style monitor (ELE-0190). You simply remove the old...
You likely have a problem with your spindle controller card or inverter. When you get alarm #8, this is telling you that your motor is spinning with no movement from the belts, like they are off the...
Yes the motors are the same and you have a MTR-0002. You can exchange them to test out the motor. Likely you will need a full rebuild, but check the brushes, both amature and Tach. While the motor...
CENTAUR91,
I think you are getting an alarm #3 is because you need to change the jumpers when changing boards or it will not read the correct axis. Follow this link and follow the directions on...
If you are working on a MTR-0002 you must remove the cover bolted to the face of the motor. Remove the end from the motor and the resolver will be staring up at you.
FadalCNC Tech Support
Agreed, just dump the reservoir and fill it back up with Turbine oil. The system will flush out the Vactra #2.
FadalCNC.com Tech Support
As you are doing your repairs and setting your backlash settings, we have all the parts you might need to get your machine production ready. Here is a link to the downloadable documentation for your...
Cfin, it sounds like you have done your homework on this project. I have never seen anyone do this before but it sounds like it might work. You will need to replace your ballscrew for the extra...
On the thrust bearing issue, we stock and offer the bearings you need as well as the seals. The bearings already come shimmed and ready for installation. We have all the technical manuals on our...
Just letting everyone on know that we now have replacement spindles for Haas VF machines. We designed the Fadal 10k spindles and have sold them since 2003. We now have spindles for Haas VF machines...
SlowTwitch,
AMC is a good drive and I will assume you have had it for years. We offer the identical, however updated AMC inverter so your exchange is plug and play with no little tuning or...
The 8k rpm machine will have more torque but for what you are using it for, I would definitely upgrade to the 10k spindle. The 8k spindle is the same as the 10k spindle so you won't need to exchange...
Yes, they are replaceable and we sell them all the time. We also use them in our rebuilds. Give us a call and we can get one out the door to you today. The part number is MTR-0090 and we have...
Gary,
With the power off, all you do is find a small straight slot screwdriver and press in on the front hole below the wire input on the terminal block. The wire should release.
On your way...
Sir, let's get back to the rapid issue. I assume it is still far too fast and still having to keep the rapid at 25%. I would try replacing the clock card (1020) and see if this helps. It is this...
It may be high but not high enough to cause this problem.
FadalCNC Tech Support