Hi Guys, I figured it out. When using feed rate in the gcode you have to have the fall down set to 1 to utilize the full speed of the gcode feed rate. This is why mine wasn't reading the correct feed...
Type: Posts; User: suade907
Hi Guys, I figured it out. When using feed rate in the gcode you have to have the fall down set to 1 to utilize the full speed of the gcode feed rate. This is why mine wasn't reading the correct feed...
Hi guys, anyone on here have a Laguna IQ or a machine with a RichAuto A11E control. I have a problem where my machine has all z axis feed rates overridden by the set work parameters speeds when you...
I've used a pierson workholding smart vac 2 system in the past. I would assume you could do the same with your Becker but you would have to make a aluminum fixture or comparable. Then use a o-ring...
Application for what you can cut? No, one just will cut slower because it can't flow the same rate of water. Thus you will need to use a smaller orifice/nozzle size.
Look up a company called Creative Edge they specialize in waterjet cutting stonework for flooring applications. I've been in the business for over 20 years and they do some of the finest work I've...
GMA is the same quality as barton just cheaper. At least the 80 mesh alluvial garnet is.
Or is that against the forum rules? I could not locate a classified section? Our company is moving to Michigan and we are selling two pumps a jet edge 55-150 and a 55-100 as well as a esab high rail...
Look for chips in your plungers like small flakes missing. That will cause you to go through seals really fast but at 5600 hours that is very rare. A chip in a plunger would be cause for a new...
Having a 50 hp pump typically will allow you to run a 15/45 nozzle orifice combination. But most people with 50hp pumps run a 14/40 since it's less wear on the pump. A 40hp pump will not be able to...
I just tried updating today and almost wrecked my tools. I'm lucky after the update and restoring my tool settings all my stuff was off by about a half inch, why? Who knows? This really sucks, I've...
Hi guys, I just wanted to thank the OP and everyone for delving into the intricacies of the Tormach 15L. I've been keeping an eye on this lathe for a while now and I'm finally getting ready to pull...
2 flute center cutting for aluminum to prevent clogging. Carbide if you can afford it but ms works fine as well.
Sent from my GT-N8013 using Tapatalk
Check your g-code first.
Sent from my GT-N8013 using Tapatalk
I think you will be happy with either unit. Both are costly but you will be getting solid machines. I have a accustream pump and can say first hand they are great. I believe ward bundles them with...
If you can build one more power to ya, but the Bart is a proven device and it works very well. Over the long haul it will pay for itself many times over. After a person shovels their tank for the...
We bought a shopsabre sidekick 48x96 a year ago. Its a little more than your budget but was well worth it. Steel welded frame and linear guides and bearings all around. It's been a great machine for...
You need a Bart wand. It's the most affordable way to clean your tank. It's made by Barton.
Sent from my GT-N8013 using Tapatalk
Yes shortest tool you can get away with, carbide is better and use 2 flutes for aluminum. In aluminum a good carbide bit will last a long time. If you ever hear chattering your shortening your bit...
I agree the more rigid you can make your entire setup the better. Typically you'll want to cut that from right to left from my experience. The rotation of the tool forces the piece towards the most...
I'm gonna save you a ton of trouble if nobody has mentioned it already. Go buy a program called ME Consultant Pro. I've been a cnc programmer/operator for over 14 years and have never had any formal...
How much? Does it have ramping built in?
CNC programmer/operator wanted for waterjet and mill operation in Homer Glen, IL just southwest of Chicago.
P.I.W. Corp. is a Metal fabrication shop in Homer Glen, IL We have 3 waterjets and 3...
Where are you located? I have one near Chicago. I purchased it a few months before Christmas. I love the Mach 3 software and the machine but I would like to move up to a larger machine. I wasn't...