Search:

I have a leadwell ltc15, same as Mori al20. I smelled and saw smoke at the top of the tool changer. The tool changer motor was cold, the x axis servo motor was cold, I removed the back cover of...

What system are you using and what does it cost?

The 5v voltage regulator, fastened to the 1 inch tall heat sink is probably a 7805. 7805ct is rated at 1.5 amps. These are very cheap on ebay. I have changed to one of these which did not fix the...

Please email me the files at [email protected]
Bob S

I have never seen anyone just load the parameters. There are issues as to when the machine knows the baud rate and when the screen has the right resolution. I have only seen them entered manually. ...

I have restored these a few times and have one to do in the next week. You ussually need a new 3.5 volt battery on the board that preserves the parameters when the machine is shut off. Even if...

I have a leadwell lt15 ota and it has ussually been the same as a Mori Seiki

I get error 1002 soft limit 2, z axis is opposite zero end. I have about 17 in the work shift and the alarm comes at about 17.4 by the actual machine coordinates. I need to move .5 in the z minus...

I am still looking for sanyo encoders rst5x and other parts for medlas and okk from the 1980"s. Please reply if you have parts or trouble shooting infor.
Bob

You need to review parameters. When you find the battery that may be maintaining the memory, do not disconnect it. I put the same voltage in parelel before removing the battery. Some times you can...

I wrote the same report. We both got the same conclusion. Is that peer review?

I got a lot of help from Mits. I was asking the machine to do things when the machine tool builder option tables were not turned on. Basicly we told the computer that an index table was present. ...

When I open the parameters with h1000-2=1 and enter 2 times , then 1 and push the top parameter key, I get 3 pages of inputs suppied by the machine tool builder. It contains things like the labels...

I have a mch450 and pcv-40 okk both with meldas m86 controllers. I call mits often and have nearly every manual. I can not find this error message listed although I get it often when the machine is...

I did not have the right option parameters. I have a set from okk that made some functions work. I could use the options used on a pallet changer. Looking at other okk option tables would help me...

I get the same error on m86 when I try to write a new program or program number in edit or mdi or if I try to input with the rs232. I am also reloading parmameters. I am working on mch450. MY...

cadem.com is the free ware i use for one machine. I could never find out what the paid programs cost or will do. the free section is a bit hard to locate on their page. It works well.
Bob

The sensor we removed did not have any numbers on it. The cable had 7 wires in it. I have the frequol manual that tells how and where to install and set-up.

This crushed sensor is on my Okk pcv-40. Medas M86, freqrol mod fr-se 7.5. Everything was working until we mechanically smashed the sensor. Will the sensor you have work on it? Bob

I have been thru this problem recently with a M0. It looks as if your battery is dead. MIts at 847-478-2500 gave me a restart procedure that started with push 2 soft keys at once. I entered the...

I have a mitsubishi Frreqrol mod fr-se 7.5. The Freqrol manual says the orient requires a + -10 volt signal to make the orient function work. There is a magnet on the spindle and a detection...

I am having trouble finding a new sensor. We mechanically broke ours. It has the key word macome and lbo and c1730. I use a mits freqrol fr-se. I think the controller needs a + - 10 volt signal. ...

Since Galesburg is cancelled has anyone proposed something else? I would consider one in Louisville KY. I have about the same building space available as Cardinal.

I am in the process of making a cnc dresser and maybe other controls in a centerless grinder. I have been accumulating the motors and drivers for 2 years. I need info about bar grinding to choose...

I have blank pages on 4 thru 10. On page 11 I get the zero point options. The problem is when I do g28 b0. the machine position screen shows 360.035 and when the table clamps the machine display...

I have a meldas M0 problem. I also don't see how to start a new thread. I have most of the docs for this okk mch450. The rotary B axis does not stop at the right place when I zero the b axis. It...

As it has turned out several other problems occurred and in solving those this 605 alarm is gone. The b axis gain was making the servo motor oscilate. We disassembled the motor from the machine and...

I have an error code 605 keeping my mch450 from starting. Do any of you know how to fix that.
bob

Mitsubitsi has confirmed what you said. I have found my Mach3 program will run a demo program all the way thru that Mits will not run because the end points do not match. I am redrawing everything...

This code stops with an error 39. on my okk pcv-40 meldas m86. Does this machine recognize an “R”. How do I change between incremental and absolute center of the radius? When do I use each? I...