what about a gear change? may not have gears I have tl1 belt drive
m41 low m42 high???
running out of ideas
Type: Posts; User: gregoryblaine
what about a gear change? may not have gears I have tl1 belt drive
m41 low m42 high???
running out of ideas
G97-G98 ALSO CONTROL SPINDLE SURFACE FOOTAGE.
yes that is maxium splindle command
spindle limited in settings?
second page of selections you can probe a lenght to get center in x or y . they need to be fairly close to the same lenght. just add it to the program.
changed the battery now turret misses its alignment spot?
says tool 2 but tool 1 is in position?
HELP
can anyone tell me how to fix this?
OOPS IT IS A TL2
CAN ANYONE TELL ME HOW TO LINE THIS TL1 BACK UP ? WHERE DO YOU START????
IT IS CUTTING .015 TAPER IN 10 INCHES IN Z AND .009 IN 5 ON X
some isn't straight shouldn't have to program it out, spindle is square to carriage but x axis is way off
HOW DO I FIX A .01 TAPER ON THE FACE OVER 7 INCHES
NEEDS TOOL OFFSET IN X
HI I HAVE A HAAS TL2 AND THE FACE IS CUTTING A .01 TAPER OVER 7 INCHES, THE HAAS REPAIR GUY SAID TO RIP THE MACHINE HEAD OFF AND CUT THE BASE TO ALLOW ROOM TO MOVE SPINDLE ASSEMBLY AND REALIGN. WELL...
can someone tell me what radius is cut onto hard jaws. I have a chuck with very aggressive teeth and want to cut them back so there are flats on them so what is the diameter they use to cut chuck...
I NEED A BRASS GEAR INSIDE THE BOX FOR THE COOLANT HAAS DOES NOT SELL THE PART JUST THE WHOLE NEW SETUP DOES ANY ONE KNOW SOMEONE THAT MAY HAVE THESE PARTS LAYING AROUND
i would say u have to use the g73 code becuase of the wrong movements it doesnt want to take in a cycle
turret off center by .125 high no room in adjustments to get that much took off turret to see if anything wrong inside. it is fine
i have the service manual. cant upload
if i needed a smart ass remark im sure i could have found if without getting on the net *******. fyi haas tech could not help me he didnt know what to think was the problem. but im sure you know what...
it is a haas sl30 all sensors have been clean adjusted and cleaned and adjusted again. still no advail
:drowning:hlo i have taken of the turret on a sl30 and after putting it back on it will not index to the proper locations. it will go home at t1 but if mdi to t10 it goes past and around to t6. it...
can anyone tell me the difference between circular runout and total runout?
:confused:
i have found out that in the settings
k02 bit #7 can be changed and it will let the door open
New Problem now when the door is open it will not rapid full speed
any ideas around that???
we have a new hardinge su250 lathe
we would like to over ride the door switch but cant seem to succeed.
does anyone have any good ideas to turn off the switches?
it will not let you disconnect...
does someone know how to stop this control from ending a program with no tool? Every time it comes to the end the machine puts tool away and leaves the spindle empty. I am only using 1 tool and there...
have you got this fixed ours a sl20 also. the chuck just dont hold the part can be pushed right down the spindle. Haas gave us different jaws that are sharp but they dig in not to good for a finished...
we have a new haas lathe and there has been a very big problem with the chuck holding. it keeps pushing parts. and or spinning it. has anyone else had any problems like this or is it just this lathe?
Does anyone know how to get around the warm up cycle on a new hardinge lathe. If the power fails it then has a six minute warm up and I would like to ignore it. can anyone help?
40 and going strong
ive been doing it all for 18 years in a job shop with all different types of machines. we had and old eagle cnc, a couple aof mazaks, hurco haas they are all have there good and bad points
there is an m code to change coolant position ,m34 ,m35 it think. but you would have to go with a g80 first.