I have tried rfqwork.com, I can't reply or bid on any of the jobs. I get a message saying that I do not have permission. I can not contact the admin through the site either. Can you please help?...
Type: Posts; User: ranchak
I have tried rfqwork.com, I can't reply or bid on any of the jobs. I get a message saying that I do not have permission. I can not contact the admin through the site either. Can you please help?...
nszzya, I need an email address to send your quote to. Thanks, Ron
I would also like to quote your part. Please send a drawing to: [email protected]
Thanks, Ron
I think I might have found the problem. There are two limit switches that are on the spindle lock cylinder. It looks like one of them may be faulty. I have two new ones on order and will replace them...
Thanks for the reply tc429, I found *sstp. It is address G011.5. I have a copy of my ladder that I can send to you by email. I can not find spcnt. Thanks, Ron
I have an 1986 Acromax MX-16 Mill with a 11M control, NO gearbox. Recently I have had a problem where the spindle is "stalling" intermittently in a cut. I use the word "stalling", but what is...
I have a Acromax Mill with a 11M control, looks just like a Matsuura MC500V. In MDI mode today I typed in a tool change, but by mistake entered a tool change number that I don't have. I am now...
Avast goes crazy when I access this site from my shop PC
I'll pick one up the next time I order, I can see where it would be handy to have around.
Thanks for the pics JR. I should have bought the planar gage, but I have things worked out thanks to your pics. I am using the collet closer on the end because the collet indexer is set up to run...
I got the tail stock today, exactly what I thought, cheap china stuff. I'm not too keen on using this, I guess I'm back to the drawing board on these. I should have bought a second collet indexer.
I have the service manual, pm me your email address and I will send a copy to you.
I ordered the tail stock today, should be here tomorrow, will see how that works out.
The wrench flats need to be "clocked" to each other.
Try these guys: [email protected] They have an office in England
UPDATE: I purchased a used Yuasa 5C Collet Indexer as many of you guys suggested, it works GREAT! All of my flats are now a consistent depth. One thing I need to figure out now is I have some rods...
On the longer parts I used to use two blocks to support the opposite end. One thing that I liked about the collet block was when doing flats on both ends you didn't have to move the x-axis to machine...
Thanks for all of the help and suggestions. I'm going to get a collet indexer and see if I have any better luck.
Flipping the block.
I don't have a taper issue, I have used an extra block on the end of the longer rods to add stability. I know there can be some error in the material itself, but I can't believe it's what I'm seeing.
holbieone, what do you mean? concentricity?
Here's a pic of my setup. I checked the block with an indicator, within .002" on all four sides. I'm about ready to get another set of blocks.
183676
"The prefs stick, until it is launched in "free mode" which strips everything down again"
I don't think you are correct about this. I don't remember opening Predator from my desktop, but I do know...
I'll post a pic tomorrow. The collets are Crawford brand, they are new and haven't been used much. I don't notice any runout when using them in the lathe. I have had the same problem machining the...
This is not a BobCad problem, but I know there are some really smart guys on here and I really don't want to hear all of the BS on the General Forum. I have been having a problem machine wrench flats...
I had to reload Predator and it worked fine for a while, now it's back to black and white again. I also noticed that I can not re-number my programs.
Hey TonyW, is this what you mean:
182500
That was it, not too sure where the duplicate arc came from, thanks, Ron
I'll give that a try tomorrow.
I have a simple profile and for some reason BC doesn't want to follow it. I have tried about everything that I know to do, but there must be something simple that I am overlooking. I've attached a...