Is it possible to output the operator keystroke pages?
We ran the turret into the chuck and I am trying to figure out what happened. (Yes, pretty much at full rapid speed.)
Type: Posts; User: bk1955
Is it possible to output the operator keystroke pages?
We ran the turret into the chuck and I am trying to figure out what happened. (Yes, pretty much at full rapid speed.)
We are considering an Adira shear. 1/4" max cutting capacity. Anyone have experience with this brand of equipment?
Yes, I know this is an old machine, but it's all we have and does not run a lot. We are making some in-house tooling that requires a 5" tall cut, which is a lot for this machine. The configuration...
I am looking for the Fadal tech right now.
By encoder, do you mean resolver? Where would that encoder calibration be? Also, this machine does not have scales, as we saw an "SV" command and we wonder if that is what you meant. There is a...
We have a 1996 4020 with factory pallet changer. We have a simple job of drilling holes down a part the length of the X axis travel. The actual measured distance started out .017 less than the...
I have had one of these for several years for my home shop use. I had not run it in several months, maybe close to a year. I get a Gross Positioning Error Y C. I checked the motor cables, brushes,...
That board is part of the KTK drive. I do not have a diagram. The drive has been a problem on my machine and I would like to upgrade it if possible.
See my attachments, they may help.
This is the info on my machine.
LOOK very closely to see if it matches.
I am in a similar situation today.
What did you end up doing with this machine?
The brush length is about 1 3/8.
I started up today and manually ran the spindle up to 3500 rpm. I ran a short program with no tool and it was OK. I ran the program in the cut, 5/16 end mill, 3/16...
I have a TNC 2500. I have a standard purchased 9 pin to 25 pin cable. I have what is called a "null modem" adapter on the 25 pin end at the machine. It would not work without it. Set the control...
I have the wild leg correct. I have run for several years without a problem. I agree that the low voltage is the place to start. I have capacitors on there now, but at some point reduced them, I...
I have to go back to the beginning on my install several years ago. I could not run. I have a phase converter panel built by Des-co, who is now out of business I think. They had me wire in some...
Do you think those voltages are far enough off to cause a problem?
Sent from my iPad using Tapatalk
I know it has been awhile. I have been nursing this thing to get some work done. My voltages run 233, 244,244. To ground: 120, 208,120 Hi-leg Delta. I suspect the old KTK drive, as I have the...
I'll try it and post what I find. Thanks for the help.
Yes, that is the message. I am running on a 20 horsepower rotary phase converter. I have added some run capacitors when I put it in and at my old age I don't remember where that idea came from. ...
I have an Interact 1 MKII with the Heidenhain 2500 control and KTK spindle drive. Periodically and more lately I have been getting spindle faults. It seems to repair itself if I turn it off and...
Are you talking about the 900 series rubber flex collets?
I am writing a new post for the Fadal Format. How do I get it to output the E value for fixture offset? I am not sure where you enter the number in the program? Is it under "M" funtions - datum...
What you are saying makes sense. Someone had posted some time ago some service sheets on the KTK drive and the MT1-1 board. I found on the MT1-1 board some adjustments. First was the amp...
I have an Interact l MK II with the KTK drive (Heidenhain TNC2500 Control). When starting the spindle I am getting a "Spindle Dirve Fault" alarm. I can reset and wait and sometimes get it going and...
I have an Interact l MK II with a Heidenhain TNC 2500 control. Everything is up and running and I am using Heidenhain software to load and download programs with no problem. I have a paper copy of...
George,
I have this control (TNC 2500, Interact 1 MKII) and I am trying to figure out how to download the parameters to the PC for safekeeping.
If I get into the parameter page and hit ext, it...
I owned a small shop from '87 to '95 and never felt that it was going to go anywhere for 2 reasons: There was no growth and so much tool work that I was getting at that time for larger local...
Has anyone used First Index for leads or getting work? Did it pay off?
Thanks for the info, I have a very low hour machine and I am hoping for the best, but one of the boards did give me some minor problem already.
Thanks again.
I have one of these machines, how expensive and complicated is it to that drive conversion?