Hello dr0g0,
We have several different procedures each with its own step-by-step set of instructions based on the motion card/box model, what is being seen and the product version you have.
If...
Type: Posts; User: camsoft
Hello dr0g0,
We have several different procedures each with its own step-by-step set of instructions based on the motion card/box model, what is being seen and the product version you have.
If...
John,
To answer your question directly as to where the 24V wires connect to are shown in the diagram & description on page 8-19 of the installation manual.
The CS-16600 motion board is a...
Bobk,
Yes, it is a direct replacement.
The logic routines and commands in the CBK file as well as the operator interface and all wiring will remain the same.
The 4143 motion box and the...
We have done both the red end cap Fanuc AC brushless servos as well as their DC permanent magnet brushed servos. Many of the AC models have "pulse encoders". If so we have retained them. Otherwise...
Yes, it is possible to reuse most older model Fanuc Servo motors and drives and some newer models.
We have done this hundreds of times since the early 80s. We can also provide the wiring charts once...
Flavio,
We received your e-mail. Thanks for the description.
We have sent you instructions on how to download a demo plus few other technical e-mails on 3D Printing, CAD/CAM and Raster to...
Hello Michael,
We do offer low cost CAD/CAM software that imports DXF and other CAD files that can create .NC files as a standard feature.
AS3000
We also have a system that can control...
Sorry, no.
While we do offer CNC Punch Press Software, this is not ours.
Tech Support
CamSoft Corp.
[email protected]
PH 951-674-8100
Fax 951-674-3110
CNC Controller, PC Based CNC...
NelZ,
We noticed that you asked us these questions directly last week via e-mail. We thought since you posted here that we would reciprocate the answers here as well. Thanks.
So your question...
You'll to get this post processor from the CAD/CAM software supplier or ATEK directly.
Tech Support
CamSoft Corp.
[email protected]
PH 951-674-8100
Fax 951-674-3110
CNC Controller, PC...
Steve,
In the CNC Lite version you could set your user named variable to an internal variable and display it in the watch window or else display the variable in your program in the TIMER.FIL file...
CamSoft has two methods to do parametric programming.
In G code we use the traditional math functions and user defined variables along with a set of M codes to do IF THEN , > Greater Than and <...
Typically if you keep it up it's only $16 to $41 a month which includes tech support with one of us, free software updates to the current version and new printed manuals plus CD tutorials and post...
Mark,
We have not received an email asking a tech support question from your address to [email protected] since January 2016 regarding M7 and M8. We did get a test email at the end of...
Mark,
You wrote "OK now just need for CamSoft to come back on the error message"+"Still cannot get CNC to work it tells me to ring and give the serial number, not sure when the best time to do...
Mark,
You mentioned that "I didn't receive the 2017 update, last was 2016, don't know why at this stage have asked Camsoft accounts to look into it as it was paid back in March 2017, so latest...
Burgs,
The current version has a built-in pre-written homing routine that does not require code writing , there are simple user settings to select from such as the homing travel direction, the...
Avery,
We read this message after answering your last message the other Thread.
Okay, that a good basis. We will need you to contact us , to get more detail on these machines. We can certainly...
This message "OVERFLOW DO NOT CHECK ALL ENTITIES AT ONCE" is saying that memory has been exceeded because there are too many entities in the IGES file. Entities are individual points, lines, arcs,...
Basically, you would need a post processor that matches the specific Dynapath model and machine type from us plus a copy of the Advanced System 3000 software.
Tech Support
CamSoft Corp....
Yes, Advanced System 3000 works with all Dynapath Delta controllers. The most popular models are the Delta 10, 20 and 40.
Advanced System 3000 also allows you to switch between Mill and Lathe mode...
We wrote our own drivers to make the CNC system better.
We didn't spend the time and money just to be different.
Early on, 20 years ago when Galil came out, they had a good product for factory...
We hear you and we'll do it.
We want people to know that we have 4 web-sites now.
cnccontrols.com
is the main site these days that we advertise and keep up with. The other sites are still up...
There are a few different ways to rotate , scale or tilt the G code program.
The 2 most common are:
G68 to rotate the part at an angle around a user defined X,Y pivot position
-or-
G140 for 2D...
Klm123
The message (rapid plane Z is same as R value) is letting you know the rapid move G00 Z0.1 is the same as the R0.1 value in the G83 canned cycle on the line before. Z would not move. It's...
Yes, you may simply delete the SMARTPTH.FIL from the CNC folder and remove the SMARTPATH ON logic command from the STARTUP.FIL file.
This will disable the Smart Path features
Tech Support...
Josh,
Something is a mis here. You would use the analog input box to read voltages. The box was checked here before shipping. All 4 analog input channels are working. There is pre-written logic...
Hello Arul,
This maybe an easy one.
There are 3 ways to control how the axis stop when a over travel limit is hit.
(1) By default the motion card it itself separate from Windows will disable...
In your case the cost varied because there was a quote sent in February for application assistance to customize your system further for better performance. We realize this is something we would...
mbam,
Yes, they should correct the Z axis position display. The settings we asked you to change should correct the display while still
doing the physical comp.
You're correct that without...