Hey guys
I am working in the middle east on a military aviation contract to support their maintenence department in the fabrication of jigs ,fixtures and maintenance stands etc. For a short period...
Type: Posts; User: esadaddy
Hey guys
I am working in the middle east on a military aviation contract to support their maintenence department in the fabrication of jigs ,fixtures and maintenance stands etc. For a short period...
Can anyone telm me how to change the "machine position" to display inch. I found out how to change the position screen to inch but the machine position still shows mm. Can anyone tell me how to...
I believe I got it now. You guys are deep. I understand my mental error now. I was looking at the position screen assuming that that was the actual machine position but it was a already shifted...
Thanks
It worked perfect.
Another question in regards to machine position.
You stated the g55 is an offset of the "machine position" How do I know I am shifting the machine position?. What I mean is that while I was able...
Well explained.
I got it now.
I appreciate the help. I have went from zero progress to fully capable in a matter of a week using this forum.
Thanks a bunch.
I get confused between G54 and H1
what is the difference.
I got the first part,but what do you mean by send z3?
After loading my programs I would like to double check my "work offset" and my tool offsets.
What is the small program that I can run to check them?
I would like to thank you guys very much for your assistance. I wanted to say that before I forgot.
I am now able to read files directly from the mem card. I had to change a setting in the param...
This happens when I try to find the file through the RMT selector switch on the machine.
It should search the mem card directory correct?
What is error code 0114 or i think 114
Fanuc oi-mb controller
Yes
RMT selector switch
The piece of manual i have says this switch is for moving programs from PC
But If so, What are the first steps I should do?
Do I need DNC software for this or can...
f_bu
I will try these settings tommorow at work.
Once the changes are made what should I do after that?
Will I see dnc as an option on the display? Or is there another path I must go down?
How do I drip feed from the card in the controller? This is what I started with but I found no dnc option in the controller
Im sorry I thought I saw tape mode but I was mistaken. If I dont have tape mode what are the other options?
Is there possible some other wording on this controller?
The controller is an oi-mb.
In my case since I am using the oi-mb controller,How do I activate this parameter 138.7?
And in the case of drip freeding. Is there any special software I need in order to drip feed?
Thank you
I will try drip feeding first
Yes it has tape mode.
Can you give me some head start steps to seeting it up.
As in
Were on the computer does the program need to be stored?
Are ther any special netork settings I need...
"Look in the ladder diagram how G43 bit 5 (xx1xxxxx) is set. Maybe not by button only, but with some keep relay+AUTO mode switch. Check I/O device=4 and parameter 138 bit 7=1"
Could you explain a...
I followed these steps and did not see any dnc option.
Maybe this machine does not have this option.
Is there any other way to run large files other that through the Memcard?
I have tried the steps but I never saw any DNC option.
Maybe this machine does not have this option.
Is there any other way to run large files. Or am I stuck with what the machine has.
Fanuc oi-mb
I may have seen 113,### somewere but I dont know if this is mega or kbs
I wll give it a try
Thanks again
Thanks a bunch!
But now I believe the memory maybe full on the machine. Once I followed all the steps you told me,the transfer process stopped all of a sudden. Then When I tried again I got the...
I belive that the memory may be full on the machine. So I have a couple of questions.
How do I remove the old programs?
How do I know how much capacity the machine has?
Can I run the program...
I will try the advice you gave today when I go in to work. Then I will let you know the out come.
I will post the program also later.
PS Thanks for the help
Yes thats correct
Fanuc oi-mb controller
How do I get the controller to pull the programs from the memcard? It displays the programs on the disc but I cannot use them.
The machine can write to the card but...
Thanks a bunch