I thank you for your help. we found the problem was a burnt circuit (path) on the I/O board, caused the thermal alarm..
Type: Posts; User: barnesbqto
I thank you for your help. we found the problem was a burnt circuit (path) on the I/O board, caused the thermal alarm..
Hello, i have the following encoder on our Warner & Swasey 315U. Data Technology P/N: DT25-encoder, Model: 2250-50/5-SR-03-209. Could anyone tell me how many pulses this has? Thanks.
Hello, we have an Matsuura MC-500V w/ M5X. The problem is this machine gets hot in the electrical cabinet (right side looking at front of machine) where the boards are. Machine will start acting-up,...
I'm just adding this to my previous post above. Does anyone know where we could purchase a set of electrical schematics for this machine. A Warner & Swasey M-5940, S/N U1102052/3155341. Thanks.
We have a Warner & Swasey M-5940 cnc lathe.With General Numeric control and, fanuc servo drive. Machine had a couple of problems. 1st. was blowing the fuses in X servo drive (Fuses 1 ans, 2) also...
Thanks for your reply. This is a Siemens spindle drive (SIMODRIVE). We did try your suggestion about stepping down the rpm in increments, but it drops out regardless. e.i. 1000 to 800 rpm drive...
Hello, we have a problem with our spindle. This has the Siemens spindle drive. When try to stop the spindle, the drive will drop out, letting the spindle coast to a stop. We are running at 1000 rpm....
Thanks for your reply. I really don't know if this is an alpha drive all i have is a number off of the drive unit, A06B-6D63-H222#H51C. This is an old Moriseiki early 1990's. Thanks.
Good afternoon, we have the following alarm on our Moriseiki SL-25 cnc lathe]EX 451 spindle drive unit alarm and, on the drive we have AL-10. We turn off machine, wait awhile turn on again, will run...
we have an leadwell VMC with the Fanuc OM control. The machine came up wit all these alarms at once (417,427,& 437) and the CRT displays "0" value in all axis. Any advise on what could have happened....
Hello, i have the following problem with our Fadal VMC 15. The spindle will not start. This always first thing in morning, and is intermittent. All we do is pull all boards out of the Vector drive,...
Good morning, can anybody advise us on where we can purchase the following items, for Leadwell MCV-760 AP, ways (X & Y axis) also, ball screw for Y axis? Thanks.
Hello, can anybody advise me on where to purchase a new or rebuilt, Fanuc servo motor, Model: 5S, Type: A06B-0314-B033. Pulse coder ABS3000P. Thanks.
ISince the last time i posted on this problem (couple of weeks) the motor was taken apart "just to check it out". Also had motor megged they said it was Ok. Now, after putting back together, When...
Hello, i need to find the procedure for installing (reinstall) the pulse coder ABS3000P, on servo motor A06B-0314-B033 Thanks.
I disconnect the the power cable for the motor from the servo amp. The 414 alm does not appear, DGN 720 bit #4 (0) was (1) w/alm. On the servo amp. pcb have the two green leds on. Thanks for your...
thanks for your reply. This happens at power up. This is a moric T4F, with Fanuc 0-TF. According to what manuals we have, it is 24vdc. I traced back from the brake through the Bestact relay (KR 19)...
Hello, we have the following alarms on our Mori Seiki SL 25. Servo alarm 401, 414. DGN 720 Bit #4, 1. We swapped the servo amplifier with a new one. Same alarm. Check power cable to motor and, motor....
I have a Cincinnati cinturn 1208 cnc lathe with the 850 acramatic control. The Monitor "died", so we wanted to use a converter to adapt a VGA monitor to this. We bought the Moncotech Model: MVC007...
Hello, our Dynapath Delta 2000 mill is hanging up about 5-10 minutes after turning on. We get no alarms or alerts, just hangs and, cannot do anything with control. I thank you for any suggestions, or...
Thanks for the tip ObrienDave. I have this set as your image shows. I don't know why it's doing the repeating tool paths thing. Even if I just select one particular operation to regenerate it repeats...
I notice that when I regenerate tool paths the thing keeps regenerating paths. It will run them over and over until finally (gets tired.) If I select just one operation it will generate all of them...