Yes, it was about the wires. There was a problem with them. Replacing the wires, the spindle began to work. But since I disassembled it before, I had to reassemble it since the cause of the problem...
Type: Posts; User: Thomas91
Yes, it was about the wires. There was a problem with them. Replacing the wires, the spindle began to work. But since I disassembled it before, I had to reassemble it since the cause of the problem...
Thanks a lot! I will run to check everything and assemble the engine (hopefully I will assemble it correctly) !! And I'll drink as soon as I find a break in the cable!
And yes, I do not live in...
Good day! I have a Chinese machine СNCest 1.5 kV 6040 with water cooling. I have attached the image. It worked properly all these months. But now the moment has come for a complex project that lasted...
Greetings! I have a Chinese machine that I bought from Amazon: https://www.amazon.com/LiFuJunDong-Engraver-Engraving-Controller-SHIPPING/dp/B07RZJW385/ref=pd_rhf_ee_p_img_2?_encoding=UTF8H7JFZ9=1
I...
It's very strange, I attached images in this way ... exactly as you explained
I found that this problem can still arise from power surges. Tomorrow I will check the USB port, try to create noise :) I want to eliminate all possible causes of the occurrence
are these diagrams suitable for all diameters? I think they can be used in conjunction with the formula
I bought these mills: https://www.amazon.com/dp/B073RKCWGH/ref=cm_sw_r_cp_apa_fabc_0NR2FbZYMVMVG?_encoding=UTF8&psc=1
I didn’t understand the moment with cutting into the material. Are these mills...
Yes, i know about compression bits, but they are minimum size is 3.175 mm, smaller i can't find. This is the only negative. I just need to cut the locomotive parts out of plywood, unfortunately I...
Oh, thank you very much! You helped me a lot!) What bits are best for cutting plywood?
Good day! I recently purchased a corn type bit set.
https://www.amazon.com/dp/B07TRFWXL8/ref=cm_sw_r_cp_apa_fabc_87e2FbJMS6844
How to choose the right feed rates for corn? I read everywhere...
I tried to attach it with tape, but this is possible if I do not make through cuts because in this case the cutter is covered with tape and starts to burn ... Fortunately, I found out that the tip of...
Believe me, a small chip in the top layer of plywood is not so scary, especially if you compare it with what is happening with me now) Chips around the entire perimeter. And by the way, I also use...
My machine is CNCest, Chinese CNC. Spindle 1,5kw 110v. I checked that the design of the spindle mount is very rigid and there is no backlash or swinging, no matter how I press. The only problem is...
I may need to use bits starting from 3mm. I tried to cut with them, but in this case, the machine starts to rattle. The fact is that I mill plywood plates 38x50 cm and I can fix them on the sides...
Thank you very much! But where i can get this chart? I searched on google but can't find. And can I use full depth cutters, i.e. 1 pass at this feed rate?
Good afternoon! I use some bits that break frequently. Now I will try to describe the bits and the speeds that I use.
At first I used straight bits with a cutting diameter of 1.5 mm and a cutting...
Good afternoon! I have good news! The problem was resolved as soon as I unchecked the Low spindle voltage checkbox This noise stopped. Freezes have also disappeared! And this is great!
With...
"No attachments, they may be to big they can be resized so you can upload them"
Do you mean the attached image is not displayed? It seems that I was able to load my pictures are displayed.
With...
Thanks for the answer! I will try to start the cnc tomorrow without a working spindle and will answer you as soon as I can. There are no problems with grounding, since I ground both the voltage...
Good day! I have a CNCest 6040 Chinese 4 axis machine. I have been using it for a month now. There were problems. The spindle accelerates and starts to emit a strange squeaking sound similar to...
Hello! I had a problem when operating a cnc machine CNCest 6040. Recently I was cutting plywood when the machine suddenly turned off. Does not respond to the switch. Opened the box hoping I could...
Did you mean that you need to click on these checkboxes?