Search:

1

AVOID AVOID EMACH PLASMA, no THC fitted, massive EMC and EMI problems,

what is the make of the servo drivers?

Needless to say, I'm an expert on eding gear, having manufactured over 150 machines using USBCNC control

Bert Eding is a super guy, I've purchased around 100 units from him, and his aftersales support leaves most of the world in shame

Im puzzled, what do you mean by directory and in what?

Just slave the one motor off the other, the encoder is just feedback to keep the co-ordinates absolute,

Switch 4 on stepper drives, if it is on your using 100% holding torque, this creates heat, switch it over and it will be 40 to 50%, thereby giving less heat,

Please let me know if you have issues with EMC and EMI, the panel is impressive and very well laid out

Hi I am the senior technician for Emach, if i can be of any assistance please email me [email protected].

Im looking for an ENGLISH manual for the aut-drive inverters, model number unimportant.

any help would be of great appreciation.

check power to the inverter, there is an overload in the panel, reset this.

Have you put a clock on it, put a clock on the base and have the needle running on the chuck, turn the chuck by hand and see how far the run out is,

thats the only way to see if its a balance,...

How have you got on?

I am an ex service engineer, recently promoted to General Manager Of Emach International Ltd, EMACH CNC Machinery, Plasma, Routers, Engravers and Machining Centres

I also...

I dont know what the status of cnc programmers are in your country but here in the uk, there are plenty so the salary is a lot lower, I am a service manager recently promoted from service technician,...

change your step size down to 50, and try again, also check your acceleration settings, they really should be between 2 and 5 times the velocity setting.

have you checked your tool length compensation g43?

If the supply is overload it will pull the voltage down, is there a pot onboard that you can adjust or is it a fixed voltage? we use Balluff 24v 5A and 20A supplies these are very stable with...

is there a macro file in the program folder or a cnc.ini file, if so i can modify this for you.

Always use shielded cables for your motors but only connect the screen at one end, EMF noise induced into the system can make it unstable. consider looking CNC Community: SINUMERIK CNC4you - Siemens,

Most noise from spindle motors is down to balancing, if the spindle and tool is perfectly balanced, including the collet nut, then noise should be to a minimum,

yes, strap a cable to the spindle, whether it be on its fixings or tapped to spindle, then just connect to a ground on the carriage.

the TLO works by pulling down the +5vdc to ground and stopping...

Estun EDC, excellent choice, be sure to tune them well, we had problems with syncing both motors on Y axis, until I fitted 20:1 gearboxes and still achieved 25m per minute, using 4:1 gearboxes...

That is correct, to help you understand, download from www.Vectric.co.uk or com their trial vcarve, you has diagrams on material setup.

My mail is [email protected] if you want to contact...

are steppers going to be beefy enough, why not use servo?

Hi, I am the senior service manager for EMACH CNC Machinery, Plasma, Routers, Engravers and Machining Centres
With our stepper systems I use the 806, they are so reliable and smooth, the torque...

Hi,

I am the senior service manager for emach uk, EMACH CNC Machinery, Plasma, Routers, Engravers and Machining Centres
We build cnc routers, plasma and laser machines, along with 3,4 and 5 axis...

Hi all, Im trying to obtain an English manual for the inverter below, any help would be appreciated, I'm willing to pay for it, or even a copy if I need to.

AUT-DRIVE DVA-4T0037G/4T0055P, the...

Ok just make sure your controller is setup correctly for machine bed size, if its -## as opposed 0 then the program will look offset

hi can you please mail the signtek and dsp controller software and any other ifo you may have, Im a service engineer for EMACH CNC Machinery, Plasma, Routers, Engravers and Machining Centres and I...