I need 5 axis powermill postprocessor pmoptz for FANUC 0i MF Plus CNC Controller.
Please help! How shall I do?
I use powermill 2019.
Waiting for kind reply.
Type: Posts; User: amitkumar171
I need 5 axis powermill postprocessor pmoptz for FANUC 0i MF Plus CNC Controller.
Please help! How shall I do?
I use powermill 2019.
Waiting for kind reply.
I need 5 axis powermill postprocessor pmoptz for FANUC 0i MF Plus CNC Controller.
Please help! How shall I do?
I use powermill 2019.
Waiting for kind reply.
Hi tom,
I am using dynomotion kflop board and kmotion cnc software. I want to know about look ahead parameter in kmotioncnc.
As i have seen in many cnc machines look ahead parameter is in...
Hi tom,
Thanks for your reply,
I tried the above method for the tool offset led toggle, i am facing one problem that,
When i am turning power on the kflop board its remembering its last...
Hi tom,
Thanks for your reply, i am having some problem while running the above c program,
The issue is When i am starting KmotionCNC.exe first time then it runs fine.
But when i am...
Dear tom ,
I want to implement tool height compensation in kinematics.c file.
Please help me how to proceed with that.
I want my machine kinematics to be adjusted by using tool length in...
Hi all ,
I am using Kflop Board , in that board i am connecting pin IO 0 AND IO 6 to my limit switch for y axis. IO0 for positive and IO1 for negative.
When i am trying to move y axis from 0 to...
Dear all
I am using kflop motion board and KMotionCNC.
In that software as i have seen that in fixture offset table X,Y,Z,A,B,C only these axes available but i want to offset U and V axes as...
Hi Tom,
Thanks for the information.
I had some more doubts. They are as follows :
1. In the FPGA datasheet it is mentioned that the operating frequency range is 5-300MHZ and 5MHz is...
Dear Tom,
You have mentioned the frequency 483kHz-641kHz. Why can't we generate more frequency like 1MHz-10MHz?
What is the input clock frequency for the FPGA?
Regards,
Hi Tom,
Arrow mark shows, CLK is input to the KFLOP. Then How kanalog board providing CLK to KFLOP? Could you tell more.
If we write the the code, Can we generate Clock from any other...
Hi Tom,
As you told "endat" communication not possible for encoders. But, I saw in KANALOG connector specs, in that mentioned Pin no. 15 of JP14 is CLK. So why this CLK pin and What is the...
Hi Tom,
Thanks for the reply i will let you know about the updates.
Hi Tom,
Thanks for your reply.
Yes i had done this placing 1k ohm in parallel with the on-board 10K ohm resistor. So the total resistance with become 909.09ohm.
And yes i tested using...
Hi Tom,
Thanks for your reply.
I will connect that encoder to Kanalog and will try to run.
And also let you know if any problem occurs.
Hi Tom ,
I am using open collector step/dir mode.
Which line driver i should use to make kflop board JP4 Pin 13 and Pin 14 to work with open collector step/dir mode for +5V.
Hi Tom,
Thanks for the information.
As i was planning to use the following series of encoder from heidenhain.
LC415/ LC485/ LF485/ LS487
...
Dear all
Presently we are using KFLOP board and KMOTION. And we need to find the simple Encoders. For Finding the Encoders we need to know:*
1. what are the Communication Protocols supports...
Yes it takes one minute
Sent from my Redmi Note 5 pro using Tapatalk
Here are the settings
Let me knowhttps://uploads.tapatalk-cdn.com/20180911/11c34fbcd11dd07c3a8d031d0959433e.jpg
Sent from my Redmi Note 5 pro using Tapatalk
Hi tom,
i am using following g code
G1 X-3.096 Y-41.478 Z70.724 A90.021 C-3.509 F1000
TO
G1 X-5.052 Y-45.586 Z65.724 A85.092 C-5.365 F1000
Hi tom, i want to know how to turn off inverse time feedrate option for 5 axes because it is causing jerk in machine movement.
I want to make machine movement smooth that is only possible without...
Hi All
I am using Kflop board for 5 axis. But now i want to use the same for 6 axis as well.
Inverse time feedrate option available in kflop is for 5 axis only.
I want to know that how...
Hi tom ,
I tried above method still same problem is happening.
How to solve my problem discussed earlier.
Waiting for your positive response.
Hi tom,
I am using Knozz board connected with kflop board.
I have connected thermistor Semitec 104GT2 100K ohm thermistor.
When is set the temperature of 200 degrees using m code i am not...
Yes i Have enabled that option for thread to launch on power up.
Hi, Tom
I am using Kflop Estop button it is wired on bit no 16 of JP4
It is working and program for this is flashed onto kflop board.
But after power reset if Estop is enabled still all...
Hi Tom,
Yes i need this.
Yes i am measuring the actual temperature with thermometer
Hi Tom,
Thanks for your reply.
I am expecting temperature range from 0-400 degree C.
And i am getting temperature from 25 degree C to 287 degree C.
After that it is not going forward ,...
Hi tom,
I have a doubt, How to calculate maximum ADC counts to input in your suggestion above mentioned. When i am using 12V power supply, and SEMITEC 104 GT2 Thermistor. ?
What will be the...