Did you get the parameters I emailed you
Type: Posts; User: gridley51
Did you get the parameters I emailed you
Most of the lubricating oil suppliers have their own brand of neat and soluble cutting oils.
Also companies like Cromwell tools and J&L (spit) sell it.Be prepared to pay silly prices for small...
Actually it was 25 bids so reading is not one of your strengths either.These 25 bids were done with 13 bidders,four of the bidders dropped out when it got to its market value.This left nine people...
It will be INT50 taper which to you is the same as NMTB50 taper.There is a small chance that the drawbar thread may be different as INT uses 1" BSW and NMTB may use 1" UNC.
However you can also use...
Once again you prove how little you know about anything never mind the cost of stuff in Britain.
As for your suggestion on selling one of mine,how stupid are you? I buy these machines and put them...
It may be a great deal for someone based in Canada,I can assure you in the UK it's not.I regularly buy Interacts with Heidenhain controls and servo drives for less than half that price.
Maybe you...
It's an old Boss control machine with steppers and the bids at the moment are about what it is worth.
This is the UK where crap is cheap.
Don't touch it with a barge pole.
I think MF1 also feeds the transformer for the axis drives and I'd be inclined to disconnect that feed and replace the fuse and see if it still blows.
So what was wrong with the spindle drive?
Move the cursor to the field you want to edit.
Press cursor right button and you should get a split screen showing the field in reverse video and also in normal.
You should then be able to change...
GE call it reversal error.
If you are not using leadscrew compensation the backlash amount is entered in to MSD parameter AXSxx30.
It is normally entered as a plus but depending upon machine config...
Tommy,I saw your request and meant to send you the parameters and forgot.PM me if you want them,I have an identical machine.
OTOH,Ali will be able to help you.
I used to have a couple of Boko hydraulic spinning lathes.ISTR blank capacity about 28" and they weighed ten tons each.
A lot of stresses involved.
Hi Al
did the owner retain this so the operator could manually push the gantry to his start point on the plate and when re-engaging the drives use that position for the reference point?
Sinumerik covers a lot of stuff.
Tell us what the control is and what machine it`s on.
Have is been running ok and have you made any changes to anything?
This control is point to point only.It won`t do a curve.It can only go in a straight line.
Better to buy something with at least a 145 control.
These machines switch the servo drive output around...
If you look on the Heidenhain website you will find the details on these.It is not easy to find but it is there.
May be quicker calling Heid technical support.It is free but sometimes not all that...
Alignment does matter and Heidenhain publish a text on how it affects the accuracy of an encoder.
It`s not the problem here but it is a problem.
The machine does not reference automatically when switched on.
You need to pull out the e-stop buttons.
Press the control on button
Press the CE button to get to the reference page.
See how that...
Yes it`s bubble memory in a 6TB
Ask your question on the Fanuc forum on this site.
There are thousands of Fanuc 6 controls running in the world.I have some myself and GE2000`s with bubble memory.
Keep pressing MOD until code comes up.
Type in 95148
Press enter.
Parameter list will appear on screen.
Use arrow keys to move to relevant parameter.
Press DEL to exit parameters.
The way around it would be to gear the encoder.May be possible but then you need to get it to ignore the index pulse when it`s not required and take care of the backlash.
All the manuals are freely...
The encoders with 18000 and 36000 lines must be used.They must be 11ua output type.
As other people have pointed out,it`s quite plainly written in the Heidenhain manuals for the control and applies...
Probably the index pulse from the encoder is coming too close to the changeover from "inhibit reference" input.
If possible try turning the encoder half a turn in any direction without turning the...
There is a way,which I forget to turn the display into a counter so that you can see if the pulses from the encoders/handwheel are getting to the control.I can`t remember what it was but the guy that...
Could be a lot of things.
Axis on hard limit or switch stuck.
Software limits wrong.
Fauty or wrongly installed handwheel. (unlikely)
If you have the elec schematics and they show the Heidenhain...
Switch the control on.
Keep pressing the MOD button until it asks for Code Number.
Type in 95148 and press ent.
Parameter list will come up.
Use the Up Down arrows to get to the parameter you...
Al,I know but I had the same problem and tried tripping the LS manually and still it wouldn`t reference.
I had put a brand new encoder on a mill with a 155 and it worked fine for three months then...
It is not necessarily the marker pulse missing.It can also be the reference switch changeover is too close to the index pulse.Recently had that problem with a new encoder and I had to use a scope to...