Search:

Hi everyone I have three questions

1. I have Yaskawa varispeed 626-MT2 When I turn on the machine Its OS red Light turns on any body with any experience with that and
how to fix it
2. ...

Hi, I have an old hardinge CHNC4. I am having problem with collet closer. there was alot of air leakage so I replaced air with Hydrolic system. Now I have problem that the oil leaks so i am going to...

Sorry could not reply earlier yes i have the drawings and i will send u in a day or two

Hi, I have checked the techo and it is working fine. I removed the wire of reverse SCR. The problem of sound was solved but there was still difference in phase current from transformer. Now if I...

Hi, I think you misunderstood me. I am attaching the drawing of the machine. if you see spindle drive and connection strip P01. we connected a variable DC power supply to 4 and 5 and increased the...

thanks for quick reply. what is needed to be checked in tacho (I have seen it, physically it is in good condition). do you think tacho can cause the huge difference in current input.

Hi every one I have the drive and motor are of kollmorgen / inland motors

Machine : Harding Lathe
Model: CHNC4
Spindle Drive: HPA03-158100-611-5306B35
Serial : 4M-405
Spindle Motor:...

hi the dc voltage are about 150 volts

Hi, I have changed the settings back but no use. same problem. the axis error is there. what do you think the error might be the card or the servo amplifier. and what does the light on servo amp...

Hardinge CHNC4 7.5HP Spindle motor bearing replacement with carbon bushing.
the bearing is of SKF 6307-2RS1. and carbon are in pair G162 Grade. sizes are 6.2x 15.9x 25 mm with 32 mm long wire. and...

Hi when I insert either of the axis card the machine wont boot after resetting the SW1 on personality card. Can you suggest where could the problem be because I remember the cards were working last...

When I press Exit it says please select appropiate soft key and also tell me what settings/info is lost of battery dies
and can that info be revived

Images of Hurco BMC 10L

Hi, Bloke Thankyou very much for the reply. I Checked every think there were two switches on personality board on switch 1 1 was off, 2 and 3 were on and 4 th was off i changed it to what you have...

Hi every one I am new to hurco so I dont know much about it. I bought a used machine about 2 years ago its z axis encoder was broken we changed it about a month ago when we turn machine on it only...

Manufacturer : General Electric
Discription: Kinamatic Direct Current Motor
HP : 20
RPM: 1150/3450
Volts : 240
ARM AMP : 72.5 FLD AMP :5.15/ 1.5
Type: CD288AT
Model :...

Hi , I have 20 hourse Power Spindle Motor with Drive for. If any body interested Please contact the email is [email protected]

Hi, I have written a fanuc 6t Post Processor Please tell me if you find some Mistake

Hi, I have written Fanuc 6t Post processor can anyone check it and tell me any mistake can you suggest cam software for lath I am using edgecam

Hi, I have written Fanuc 6t Post processor if any one need and do kindly check it and tell me any mistake

Hi, I have a question, I have machine with haidenhain TNC 155 I want to install 4axis But I cannot find a servo drive identical to already installed so I want to know that if a but a servo drive and...

try this i am using it with tnc 155 and with program haidenhain

Thanks for reply can you send me parameter list and can you tell me that it is due to perameters I have attached the file containing parametrs I have used

Hi, I have got a problem. My machine serial communication was not working so I opened the control and removed its card and install the two comunication ICs.
The parameters were rest so I gave the...

Hi, I have got a problem. My machine serial communication was not working so I opened the control and removed its card and install the two comunication ICs.
The parameters were rest so I gave the...

Hello! I am having a problem it my machine with control Haidenhain 155Q when I turn it on an error appears Z AMP ALARM. Machine was working well When I turned off yesterday. I checked the main...

Hello Every one. I have machine Machmaker with Control Haindenhain 155Q. I am facing a problem that the machine does not move in one direction like if it is woking well in Y+ then it will not move in...