Search:

Can anyone tell me how and where to access the Y axis limit switch.

I got my machine going. It was a motion control board. It must have damaged the board when I had the 24 volt short. Any way thanks for all your help. Greatly appreciated.

Could I have a bad motion control board?

Addition info. With the machine booted up everything seems to work. I can operate the tool changer functions thru the ATC diagnostics. The light on the jog control lights up but you cannot move the X...

The jog control will not activate. I tried that but no luck. I was under the impression that you could not jog the axis until a calibration was done. One thing is that before the x,y, and z axis were...

Is there a way to verify that they are there and in tact?

Okay I have an update. I can boot up the machine and get no errors. I hit the manual button, power button then cycle start. Every thing is normal at this point. The x and y axixs are in the home...

Just so I am clear. I am removing the wire from BLK3-10 so there will be nothing on this terminal. I am running a jumper from BLK3-29 to A1 of the number 8 relay. Do I leave the wires in place that...

So can you tell me the correct way to eliminate this switch. I don't think it is just a matter of disconnecting the wires. We are talking about the e-stop on the spindle door. I want to leave the...

So I have the machine booted up and the e stop error is gone. I removed the e-stop on the spindle door and disconnected the wires going to it in the cabinet. Here is a pic of the screen. The manul...

So I purposely shorted the 24 volt blue board just for ****s and giggles to simulate the way it was and the machine booted up but still had the e-stop error. This is frustrating. One step forward two...

474516

okay I no longer have a short. The wire in question was the 24 volt going to the upper drawbar limit switch. Now the machine will not boot up. It will not initialize the navigation subsystem. I did...

An update. I found one wire on the 24volt input side. When it gets removed 24 volts comes back and it fires the large contactor above and to the right and the red emergency light flashes. The red...

How does the e stop work on the spindle door? It has four wires the 1,2 wires on the red button and 3,4 wires on the green button.

I am in the process of removing wires. Do I do both the blue and the orange blocks or just the orange?

How do I get the wires from the block? Do I need a special tool.

Yes with the orange connector my 24 volts cones back. Here is the cabinet. The problem is with the largest orange connector. The one on the top closest to the door. When I plug that connector in ...

That's it I would assume. All the sockets check correct except for the 24 volt one. No power. So the next question is does that small board convert the voltage or is it something else and can I get...

Where is the 24 volt power supply?

I did some digging today. I have no power at 24r14 which feeds the door locks. Also there is no power at any of the terminals on that strip. That strip bank consists of several input output lines...

Thank you for the reply. I am going to work on it today and will let you know. Can I just wire the individual color coded wires together and remove the locks. I don't use them anyway.

I got the error on my VMX24. My machine has Allen Bradley TLS-GD2 door interlocks. This is a first on this error and I believe it is related to the door locks. I say this only because I think the...

I have both Bodcad V24 and V2 for solidworks. My question is this. There is a Bobcad font within V24 and it is a single line font. Is there a way to load this font into window to be used in...

My tool changer will not calibrate. The drum holding the tools will not turn when asked to. I can go into the ATC Diagnostics and initiate a turn but the drum does not respond. I checked the breaker...

I have a Hurco VMX 24 and with the Bobcad posts the machine starts it's Z axis count from the point of rapid traverse on drilling operations. This is also true on the center drill operations as well...

It's air operated VMX24. I used the air valve resets to get it back to the home position but now I have a error saying it does not recognize the position. This is when I try to use it. It will go...

My ATC stopped in the 60 degree position with a tool clamped and is positioned under the spindle. This is where it stopped. I went into the ATC diagnostics to clear it but it won't let me swing back...

I want to set up four parts in different locations. I have the Ultimax Dual Display console and my software has work offsets G54 to G59. Can someone give me examples on how to define and use the...

Bloke you were right on the money. I was having the coolant issue and I guess it didn't take much to disconnect the keyboard. The plug was infat pulled out of the card rack. Thanks again for your...