Worked for me, No telling how long I would have been down without this post so Thanks
Type: Posts; User: SPRSkip
Worked for me, No telling how long I would have been down without this post so Thanks
Yup I heard this BS more than one time from Tosa tooling
Similar experience with them but I never got the parts so I cant comment on that but promise after promise with no parts actually ever being shipped.
I have with no reply yet.
I have an ongoing email exchange on another matter but sadly a reply always takes me emailing twice for an answer.
I have never received an email about my Rapid turn.
Anyone else still waiting?
Anyone else becoming dis satisfied with the level of support from Tormach?
I am starting to wonder if I should go a...
nothing from Tormach 12/30/16
Mine did the same thing when I got it and I had to change the wiring in the control cabinet.
I am not at my computer to look it up but someone will help you out on I am sure.
I did have this happen ounce. Checked fuses, powered down and back up and all has been fine the rest of the time.
Good idea but I did check the outlet and there was no power
EDIT
OK so after re connecting the coolant pump and cycling on and off a few times it is working.
Relay going bad?
Ahh IC
New problem, I have no coolant,
pump is working fine when plugged into wall outlet
button on screen lights up and I can hear a relay working when I click the button
using M8 lights the...
I have now and that fixes the referencing problem but what about the door safety?
Ok so I reloaded 1.9.2 and z and y are fine but when I reference the X axis it hits the limit switch and the door light comes on as it is still trying to travel.
Time to dig out the wiring diagram.
Not a problem with the disable setting and still works fine when I go back to 1.9. I had the same problem when I first got the mill and Tormach had me swap some of the limit switch wiring. It's just...
loaded it up and when I try to home the X axis it does not stop at the switch, it just tries to keep going?
Anyone else have this?
Reseating ram is a good idea as well
Sent from my SM-N900V using Tapatalk
How long is it on b4 it shuts down? Could be the cpu overheating if the heat sink is full of gunk
Sent from my SM-N900V using Tapatalk
The Tormach passive probe is the one I have
Sent from my SM-N900V using Tapatalk
I should add I am using the cheaper probe
Sent from my SM-N900V using Tapatalk
I have done this many times in 1.82 and one time on a. 25 Dia. Boss with 1.9
Sent from my SM-N900V using Tapatalk
Unfortunately the zero is also a hole but I have used the zero hole to a corner as well then fire up the calculator.
Thanks
Sent from my SM-N900V using Tapatalk
What I want is to reverse engineer a part and find the center of a hole in relation to the origin
Sent from my SM-N900V using Tapatalk
I really miss the ability to probe the center of a hole, I dont want to set it as origin just locate it in relation to the origin.
I ran into a problem with a taping cycle where it just stopped. Didn't call for m998?
Yes I would love to try it.
Thanks
Still looking for post information or trying to decide on a CAM program.
What CAM is everyone using with PP?
Send me your part and we will talk.
No it is erroring while trying to probe the stock for setup.
What post are you all using with HSMexpress for Path Pilot?
All the posts I have or have used with Mach 3 either throw errors or wont shut off the spindle or coolant when tool change is required.
I...
While trying to use my passive probe in PP I keep getting the error "Probe tripped during a non-probe MDI command".
When I go faster it is better but have not gone to a feed rate over 35.
Anyone...