Search:

Hi Volga!

No it wasn't successful so i dropped the project and purchased a Yaskawa drive.
I had enough with these tests and experiments!

Hi Battwell!

Thought so...
I will probably try to find a servo/drive set than fooling around with compatibilities...
Thanks anyway!

Greetings i have a MR-E-70A servo drive from Mitsubishi and i can't find a matching motor for it because indeed Mitsu uses serial encoders for feedback.
I also have an absolute 16bit serial encoder...

Hi!

VSD-E drives are versatile(parker are not that versatile because they where designed for parker motors).Normally you could interface the motors at no time with the included PDF.A note,if the...

Here it comes!!!!
I have to say that i finally made them work with parker drives.What drives do you have?

Greetings!Does anyone knows where i can find a step/dir to differential converter?I want to use a drive that needs differential encoder input,and i only have step and dir signals available.
Any help...

Thanks AI!

Always there for the rookie!!!

Thanks a lot!!!!

Hi!

It seems to me that i have a long way to go...One simple question.
My motors are brushless DC as i mentioned.They are fitted with encoders.
Also there are the hall sensors.Do i need to...

Thanks AI,

I discovered that they were merged with Gettys and already have the manual.One representative from elwood-gettys sent me the PDF.
Without the PDF you can't do something because its not...

Thanks for the answer it needs some thought!More of this to come...
Another problem arised!
I don't have manual for the motors!!
The motors are American Precision Industries/Rapidsyn Division....

Greetings again!

Im starting to making sense about the inputs but...
I put the three most important sections (in pictures)from the manual that have to do with the inputs to make the access easy!...

Greetings,

Gladly i found two Parker VIX250AE brushless DC servo drives.The manual says that it takes step and dir signals!Does anyone knows or ever connected them with a parallel port for MAch3...

Greetings!

I recently purchased 2 American Precision BLDC motors rated at 24volts and 4.8A
Does anyone know where i can find a reasonably priced servo drive?
Please note that i need a drive that...

So...

I reinvented the wheel!!!!:banana:
Lol.Some times is better to discover something by yourself rather to have it served to your table.
I think that the FPT is the most important factor...

Greetings,

I recently finished a Bronze sign for a friend of mine.Because im not familiar with rpms, cutter diameter and feed,i usually use my ear to see if the cutting process is going Ok(if the...

Guys,Guys!!!!!

The problem here its not just stoping the Geckos from moving.The thing is...
TO STOP EXECUTING THE GCODE when ANY or ALL three axes fail.By halting the three Geckos at the sime...

Hi Inspiration tool,

Is it true that by converting the PC into a controller is not good?Because you use the parallel port to send the step/dir and I/O signals out and overloading the PC?
Look,we...

Hi,

I dont know how many of you had the idea how to save a machined part from beeing ruined.I come up with some idea that i will try it tomorrow(i have to open my electronics box of the mill).
...

Hi,

I received an email From Fred Smith:

"The public DeskCNC support forum is now closed. If you are an IMService customer, you may still be eligible to receive support through e-mail or our...

Hi,

I am setting up my new mill which i converted it to CNC.I have purchased a THK BNF 2005 Ground Ballscrew.But because it was used it has 0.04 mm (0.0015 in)backlash.
I remember that the balls...

Mr Smith,sorry for beeing that hursh about DeskCNC support,but indeed even when i used the search engine didnt seem to find an answer that satisfies me.I have purchased DeskCNC from Carken inc. so i...

Hmmm...

I see.The point is that i don't find support in anyway.Even in IMS forum that supports DeskCNC.So im on my own?
Sad thing to be...

:(

Hi,

I am at the early steps in CNC and i have some questions maybe stupid,maybe good to mention.But the point is that i don't know the answers.Because i have many questions,i will post them with...

Hi again,

Can anyone reply to my 31-1-2007 post?
:confused:

Adobe,

Sorry to hear that you spent some time in hospital.I dont like hospitals because they remind us that health is fragile!!!I hope that all went good...
Life is short...sniff, OOh father...

Hi there!

I have to confirm that when Adobe gave me the starting values to fill the tabs,i went with 2650 (free)rpm(2800 servo rating)and all worked fine.Also i have to confirm that is true to...

Hi again,

I have some questions about DeskCNC.What the "buffer output" does?
What means "Meter in backlash comp" and why when i disabled it the backlash steps started to work as they should...

Thank you very much!

The settings that you proposed work great.I have 2650 rpm(measured with my tachometer).I was a little nervous at start with the acceleration value that went to high,but i read...

Thank you for the interest!

I thoughted that i was alone on that.I already read the posts and i will take them into account.I will have to make some experiments with the servos.

Is it true that...