Search:

Good morning/evening. We have a Sodick EDM that recently started acting up. Machine powers up, homes, etc. When we put in any 'G' codes, for example 'G01 X1.;', the screen says 'C007 PROCESSING...

Hi,

We are getting a 310 servo off and 313 Z-axis unready alarm on the NC. We are getting the (-.) on the servopack stating BB. This is on a Hyundai CNC. Anyways, we swapped drives and got a 312...

We have a 1991 Fanuc tape cut W0. Does anyone know where to purchase a 'maintenance drawing' manual of the machine? I was going to contact Fanuc but read in another post where they didn't have any....

Does anyone have hookup/connection info on the Okuma BDU-30A servomotor drive unit? Basically trying to find out where the 3-phase 220V connects and if any additional power is required. For...

DC link voltage (not current) abnormally high.

We have a spindle drive with top board A20B-1001-0120. We are getting Alarm 11 - overcurrent in DC. We swapped top boards and determined that problem followed the board.

Can anyone tell me where...

I found some replacement units. FYI - Autostrong M1246 and Kitagawa S1246 are interchangeable.

I'm in need of a new or used Kitagawa S1246 hydraulic chucking cylinder. I have contacted Kitagawa, but never hurts to shop around.

Bottom line, it can be one that's not working. I need a few...

Thanks for the repsonses. The spindle will not run in open/closed loop. I also tried a new PLG card/sensor; also adjusted original several times. No help. I tried a new SF-BS card. No help. Since the...

The Citizen is up and running. The original disconnect alarm was caused by a faulty pulse coder. The other alarm was caused by the pulse coder not being properly aligned. On other machines, I just...

Mitsubishi Fr-sf-2-26K. Top board SF-CA. Option card SF-BS. The original problem was a dead power supply after running the night before. Replaced PS, then found shorted IGBT in base. Replaced IGBT....

Does anyone still have access to this manual? Is there a place to download it?

Thanks in advance.

Does anyone know who supports the Tsugami CNC machine? We are getting a chuck alarm and we want to replace the sensors. Thanks in advance.

We have a Fanuc A06B-6057-H403. Anyone know where to download the operators or maintenance manual? We tried Fanuc; no dice.

Also, a quick hookup would work great. We think A, 1, 2 - 220...

The Fanuc controller is a O-B. We have the X-aixs jogging and homing. If we attempt to move the Z-axis we get a 420 Z-excess alarm. This is on the dual servo amp.

Any thoughts on what would...

I got the X-axis to jog and home. Now the Z-axis gets a 420 alarm and an occassional 424 detect alarm. This is on a dual axis servo amp. (Fanuc) No replies yet.....hello? Where's the normal experts...

I was told it is 0-t.

Thanks.

In diagnostic 720 - 00010000
In diagnostic 721 - 00010000

If I'm not mistaken, I believe the bit stands for OL. Is that correct?

Also, get a 521 OT-Z on occassion. This of course is...

We have a Citizen with a Fanuc A06B-6058-H221 dual amplifier. We are getting the 414, 424 detect alarms. We had the amp and P/S repaired. It powered up ok and X jogged/homed. However, Z took moved in...

Any other info would be helpful. At this point, I have S-canned the panel and looking for other options.

I didn't remove the drive. Are you saying the drive may use external resistors for braking? It has 3 large green resistors in the top of the drive.

Regards.

Thank for the repsponse. I checked the (3) large green resistors. They checked good. I just finished cleaning and testing the magnetic contactor. It looked pretty pitted but looks/checks good now....

We have a Frenic FSD-25AR-22 that had 2 blown IGBT's, main fuse, a few diodes, etc. We repaired all this and it ran fine for approx. 50 hours or so.

The other day when braking, it blowed the...

We have a Femco/Femtec FV-40 in need of the control panel.

www.machinetools.com/.../view/femco-fv-40e

Just need the panel only that includes the rapid, feed rate, e-stop, etc.

New, used, or...

Call David Langan @ A & D.....828 682 0727. He will give you all the info you need.

I had to change parameter 1004, bit 0 to 1 before it let me do anything. Thanks all!!!

Thanks Dan. What screen do I need to be in to do that? I selected MDI mode and enter G21 under program. Is that correct?

I also tried changing it in the "offset setting" under input unit. What do you mean by password? I know what a password is, but can you give a better description or step by step? Thank you.

We have a Fanuc 16-TT and we are trying to change mm to inches. According to the info I have it is parameter 0000 bit #2 INI. We now have a "0" which is metric and it needs to be a "1" for inches. ...

We have a spindle drive A06B-6111-H026#550 and spindle motor A06b-1411-B150, x22/7000i with a Fanuc controller. It is set for a max speed of 6K rpm's. Does anyone know the parameter to change it to...