Search:

I doubt I could lend any guidance because it worked for me without any fussing that I can recall but eSS with Mach3 on Win8 definitely works.

Saw in another thread you have Gecko 203Vs. You can run the motors at 72V.

Depends on the drive. What drives are you using?

Tools>Options>System Options>Default Templates

Check the "Prompt user to select document template" option.

SPRUT Technology, JSC.
Office 6, Autozavodsky pr. 1
Naberezhnye Chelny
423815, Russia

Keling drives are relabeled Leadshine drives. Google Leadshine and you can download Leadshine manuals that are more instructive than Kelings'. SW4 = On for 1/2 current at standstill per Leadshine's...

I posted this over in the Controller/Computer forum but it's got so much Keling content that I figured it'd be good to cross-post it here for those that don't troll every section of the 'Zone.
...

I thought some 'Zoners might be interested in seeing my take on what will eventually be a 6-axis controller box (it's only 4-axis at the moment).

Housing: 5U Rack Server
Computer: AMD-based...

Replying to my own thread with the answer in the event that someone needs it in the future. John at Leadshine thanked me for pointing out the ambiguity and advised that SW4 should be ON for 1/2...

Has anyone verified the SW4 setting? If so, which way sets it to half of the dynamic current? The reason that I ask is that there is an error in the manual. In Section 7 there is a small drawing...

It worked for me. Ultimately, I decided to set the drives up with the switches. It did, however, allow me to verify functionality of the power supply, drives, and motors before I had a BOB and...

Go here: DM856 Stepper Drive - Leadshine Technology Co., Ltd.

Click Downloads.

Click RS232 Interface Pinout.

You say, "If the radius or hole is large then it’s not too bad," and then you go on to say, "at .5" and up it gets really choppy.". Did you mean to say, "at .5" or less"? If so, is it maybe...

Go to leadshine.com and look at the user manual for an M550.

Long shot here, I'm sure....

Does anyone happen to know what component pops when a KL-8070D (or, any digital Keling drive, I imagine) is powered with opposite polarity? That is, when + voltage is...

The efforts extended by those of you who replied is much appreciated. The job has been awarded.

Thanks,
AP

I'm soliciting quotes for the attached part. I've uploaded a drawing and the ZIP file contains a STEP file of the part. There will probably be other parts needed but their design has not been...

Tools>Options>System Options

Uncheck the box next to "Single command per pick".

I'm 99.99% sure that's your problem.

AP

I don't necessarily have a direct solution for your problem but would like to offer this up as it may help you figure out what's wrong:

If you're saying that the 862.861 dimension in the first pic...

I have a question, if you don't mind...

Did you consider a gas spring instead of the air cylinder? If so, what was it about them that caused you to reject them as a solution?

I ask because I...

I can't get wrap to work on conical surfaces such as the OP's project. When attempting to select a conical face, it puts up an error box that says, "Sketch plane should be parallel to a tangent...

FWIW, in SW '11, it is not necessary to create the reference plane 1/2 the diameter from the center. You can sketch on one of the primary plans (as long as it is perpendicular to the revolve axis)...

I don't know if MC works with multi-body SW parts but here's how you can do what it sounds like you want to do:

Start a new part.
Insert>Part... (select your previously designed part).
Before...

"Convert entity" will project a profile from previously created geometry to the current sketch.

Otherwise, as Jerry says, you can just select the existing geometry directly while sketching. ...

HTH means Hope This Helps
AP are my initials

AP

I duplicated your first picture by selecting the Right Plane as Reference 1 and set the angle to 25 degrees. Your second pic was duplicated by selecting the Top Plane as Reference 1 and setting the...

Tools>Options...

"System Options" tab

"View"

Check box next to "Reverse mouse wheel scroll direction".

Jack Screw

FX380 will be much, much better.

OK, this is pretty straight forward.

Edit the sketch that defines the path of your sweep.
If you have not done so, add linear dimensions to each leg.
On the top menu bar, click...