I have look at several thread and video . All these are great but my electrical is very limited. I have the #8,9,10 hook-up to the vfd so I can controlled the 0 to 10 volt. I'm just wondering which...
Type: Posts; User: Maurice
I have look at several thread and video . All these are great but my electrical is very limited. I have the #8,9,10 hook-up to the vfd so I can controlled the 0 to 10 volt. I'm just wondering which...
thanks for the info I'll be doing some research on how to set-up into mach
Hi , I have a Triac mill that I'm setting up a G540 and a Galt G200 VFD need some help to get both of them to talk to each other also using Mach III for a software
Hi could you tell me at what place this selector is thanks
Moe
HI DO YOU STILL HAVE THIS TURRET ?
THANKS MAURICE
Hi; I know we always want bigger machine but be careful when you start enlarging spindle hole because the outside diameter stay the same and consequently the wall become thinner . This could result...
Hi
I just bought on friday a sebastian Lathe Cincinnati , and the way these work is if you would want to use the back gear you have to loosen a bolt , look inside the pulley on the chuck side and...
Hi
start my Orac and it seem that the bearing in the spindle are noisy. I`m going to take the headstock apart
moe
Hi
I thaught since you retrofiting the lathe by taking everything apart , where thinking of doing the same with the turret , if so a few picture and center distance so it would give a few size to...
Hi Julius;
see your going all the way out with the retrofit good idea. I see it has a turret, was wondering if I could get some measurment whenever you have a chance. I think it`s make it a complete...
Hi Mike;
this turret looks good did you try it and when you machine with it is there any chatter problem usally that an indication of how well there build.
thanks for the info
Maurice
Hi Mike;
your probably right that was my plan from the start I`ll prabably buy from a local supplier ,there not that expensive, I had bought the index card ( CNC4pc) when I had bought the...
Hi Mike
I've got the two axis on my lathe working and fine tuned it with the Mach program it run nice. Know the interesting part is to get the spindle running. I played a bit with the setting last...
Hi Mike;
I finally got at this project bought 2 geckodrive G203v and a cnc board C11G back in the spring. Now few month later I finally decide to put it together. I want to get the two axis going...
hi adbradley
I recently bought a same lathe as your and because it was at a good price the electronic is not working properly. I'm presently using Gecko drive for my cnc router and I was wondering...
Hi everyone;
this is one of my first thread ,I've been with the cnc group for a will but never used it to much. Got some great idea to build a cnc router. I'm with the college teaching and I need...
Thanks will check it out
Maurice
HI
Need help with an Anilam controller Series M. The crt don't won't to light up. I'm having just a small flashing point in the center of the screen. The axis still feed
Regards
maurice
Hi Mike;
thanks for the respond. I'm not sure . My experience that I have in this is I have built a CNC Router with three gecko drive. I assume I should be going in the same direction.
Regards...
Hi Mike;
I have recently purchse an Orac Lathe it partially work but I would like to convert it so i could run it with my pc and mach software. Should I stip everything out or keep a few board?...
Hi
I recently bought a same lathe ,as you did I was wondering how you made out. Did you had a chance to convert over and what software your using to drive it.
regards
Moe
Hi
This is my first post hopefully it will be successful. I've just bought an ORAC Lathe last couple of week for a good price.I have a table top cnc router that I've run it with Mach II and...