Hi,
I just purchased a used D21MiA5 robo drill.
I am wondering if a Chip conveyor out of a T21IFL would fit it?
Are Robodrill's all the same castings so the chip conveyors would be...
Type: Posts; User: 9566317
Hi,
I just purchased a used D21MiA5 robo drill.
I am wondering if a Chip conveyor out of a T21IFL would fit it?
Are Robodrill's all the same castings so the chip conveyors would be...
At M30 the machine will stop, program rewinds and doors release,
At M00 and M01 Machine will stop, spindle stops but doors stay locked
If I manually remove a tool, And then start the program, The...
I am working on a year 2000 machine and found that the memory is corrupt.
I have talked with Amada and they no longer support this vintage software and want to sell updated.
I am wondering if...
Hi,
I have built a rotary phase converter and it worked great for over 10 years
We used a older GE 50hp motor with 9 leads coming out as a idler.
I used a pony motor to start it as it is quite...
You were exactly right, A break in the back plane that was almost invisible. Repaired it and machine came back to life.
Reloaded the parameters and the Password protected parameters and machine...
Did you ever get a answer for this. I have the same problem with a Mori DL20 but they want $12,000.00 for the complete board and membrane
Well I thought I solved my problem by selling the machine. Wrong People came back and asked me to look into a new issue
They have wired up the machine and now when it powers up the controller only...
Hi,
My machine was good then it experienced a hard-drive crash. We are back up and running but there are still issues.
Present problem is the Thermal Compensation is not working properly. I...
Hi All,
I have a problem and not sure what the next step should be.
My controller is flashing BAT. We have changed the batteries and it still flashes.
We had Fanuc in and they replace all the...
I have a RT210 Rotary that went through some battles. I was asked to rebuild it by the boss so I thought why not. When I took it apart I found that the brushes in the motor were destroyed.
Also when...
Can someone tell me the differance between these. What is the difference between a Mitsubishi MDS-A-CV-110 and a Mitsubishi MSD-B-CV-110
My machine had a MDS-A-CV-110 in it but it is now smoke. I...
Was not sure of that as I have not worked on a Fanuc controller for awhile.
Machine is a NH5000, new is 2005. NC id MSX-501/2
It hAs a Fanuc 18iMB contoller
Mapps 2
Does this mean what I think...
Tried the PWE and was in MDI I want to change parameter 9985 on the Fanuc side. I believe there must be a lock out as I went to some of the other parameters and I could change them. That is why I...
I need to change a parameter on the Fanuc side. When I try to do it I get a slight Flash on the screen but no change. I am therefore thinking it is a double parameter. I am sure of the K bit I need...
Hi all, I am just finishing up putting a robot infront of a NT4250
I want tospeed up the loading cycle by doing to part transfer with the auto doors
open. Anyone here figure out how to bypass the...
Problem is positioning. Example, we rapid to tool change position, pickup the spot drill. Rapid to the part and spot the part, for example sake G54. Now rapid to tools change, get the drill and rapid...
I cannot say it just happend, We just noticed it and then found out its been a issue for awile but not sure how long.
Rapids as in GO rapids.
Hi Al have not been on in awhile how is it out west?
Well they found me a new problem. Makkino A55 with fanuc 15 controler.
Now do not laugh but this is actualy happening. Running with the rapids turned down to 25% no problems, machin is accurate and...
I am wanting to increase the memory on a couple of my machines with the same vintage controlers.
One of them I added a Renishaw probe and now have very little program storage now.
I know on Fanuc...
I have a 11 series controler. My axis motor overheated and started alarming. I replaced the motor but now find that when powered up I draw 0 amps. But when I move the axis it jumps to 12 amps and...
I have upgraded my probe but now am out of memory.
I have checked parameters and if I try to change it for 640M but machine will not take it. Do I need another board or just a chip? Where is the...
Not sure where to post so will start here. I am making permenant molds for aluminum.
I have had a lot of mold requests that have nasty isolated heavy sections that will require fast cooling . I have...
Ahh been there and done that. 25 pin to 25 pin wires 2 to 3 ,3 to 2. 7 to 7 and jumper 6 to 8 to 20 on the machine side and 4to 5 on the machine side
Machine setup parameters 8 , 2 even 19200 baud...
Sounds familar I tried mold making on my tree VMC 1050 and had a lot of problems.
Not a machine issue but a controller issue. Mine was a Yasnac MX3. Found the problem after a lot of calls and...
I have one that runs every day with very few problems.
Mine has the Yasnac MX3 controler on, and was built in 1992.
Single 24 tool changer. I am located in Canada so other
than by the net I might...
Looing for some input.
I have been running a job on a screwmachine for a few years. I am finding it dificult to get people to run it any more and want to go to lights out machining. I almost bought...
Well I need to make a choice.
I am contemplating buying 2 Haas SL10's.
I have 2 SL30s and although I am not a Haas fan I cannot complain.
They run 24/5 and I seldom see Maintenance near the...
Get the ladder books out.
Daewoo with shuttle system pallets are very simple.
The machine has check points at all finished movements.
It sounds to me that you have a pallet check switch sticking....
Start with the simple things.
Can you turn the spindle by hand?
Is the tool in spindle with the longer dog in the correct side of tool?
Can you take the tool out and then turn spindle on with out...
Thanks guys,
Redid the wires and no change. Waited for everyone to go home and sat down with the parameter sheets and went through them one line at a time.
Found the one that was changed.
Now my...