Found'em!! Looks like a great product but I am afraid of the cost. Anything else out there?
Type: Posts; User: K&T EB
Found'em!! Looks like a great product but I am afraid of the cost. Anything else out there?
I need a couple dozen rial clamps for a 35mm bosch rail. I have looked at the zimmer line of products and would like something a cheaper. Does anybody now whats out there or have a design they...
I am trying to send the machine paramiters to an Allen Bradly 7360. We can send g-code with easydnc, it doesn't like the binary paramiters though.
Anybody know of a free or cheap DNC program that can send Binary?
I have a lathe with a Fagor 8040 and an ancient Fanuc spindle drive and motor. The fanuc system has let the smoke out for the last time and I would like to update the system. Can I use a plain 3...
Looks like I'm stuck
So far I don't love camsoft, can you give me a bit of info on EMC, I see its free, will it run a full cnc with a tool change and lots of I/O?
Sam,
Why you do you say "darn" on Camsoft?
unfourtenly this doc confused me further. I think its trying to tell me what IO number camsoft assigns each IO on the opto 22 relay rack but I am lost.
Can you explain what this means? And Nice...
I found the MO jumper on the card, Gailil said on the older cards it is title OPT and this is what I got. It works as expected, sort of. The enable signal stays low while the computer and camsoft...
I do have the tool changer, my ceiling is a little low, the tool change itself will fit but I need to cut a hole to put any tools in it.
I have a camsoft PC control and the spindle is on a VFD, If I put an enconder on the spindle I should be able to use digital gearing to rigid tap.
Sam,
Here are some pics of the mill, it is smaller than the one you have. This machine was origanaly hydraulic and was updated to CNC by kearny and Trecker around 1980. I would have liked to use...
I have a Opto22 G4PB32DEC and the ICM 2900 and thats it.
Where can I see the state of the I/O on the ICM 2900?
I will work on the configuration of the Opto22 G4PB32DEC .
So if I add a "Command MO" to my to my shutdown.fil the next time I start up, the drives won't enable in told to do so with a "command sh"?
I pulled the card and I couldn't find MO pins, anymore advice on how to find them?
In the camsoft diaignostic screen it only shows I/O 1-31. Is this the I/O from the opto 22 card or a mix of I/O from the Galil and opto 22? Is there a way to see the rest of the I/O?
What...
Al, Karl,
Thanks for all the great input, based on your info and a conversion with Galil I think I have a solution.
There is an MO jumper on the Galil card that will force the card to...
Thats good to hear, torque mode seamed to be the simplest solution.
I am restoring a Kearny and Trecker Milwaukee-Matic Series Eb. It is a small horizontal cnc mill with an indexing tombstone and a tool change. Is anyone out there familar with this machine? I am...
My amps support both velocity and torque modes. Is either method perfered?
Do I need to tell the control which is being used, if so, how do I do this?
Thanks
Jeremy
Al,
The outputs I was referring to where the AMPEN, these are always high when the PC is on. I would like them to stay low until the motion card or camsoft is ready to control the servos.
...
I have a camsoft pc control with Galil DMC-18X2 motion card and 2900 ICM, when I start up my computer the anolog servo signal and the enable signals all go high and my machine runs away. At some...