I will pay for the information. Please Help
Type: Posts; User: skippyfix
I will pay for the information. Please Help
I will pay for the information. Please Help
I do not know if this is the right place? but I need help! I have a eprom number APGM7 112-281N H7 that is burnt up, I need the information that is in it to get my machine back running. Please Help
Hello, does any body still have one of these machines, I have a eprom number APGM7 112-281N H7 that is burnt up, I need the information that is in it to get my machine back running. Please Help
Hello All, I just bought a 1982 HXL with a mark century 1050 controller, when I purchased it, I was told that the turret had a over index problem, so I hooked it up and found that the hall effect...
I understand all of the diameter verses radius, what I am trying to figure out if you take a ruff cut say at .100 in canned cycle it will post .100 depth of cut, go back to the same thing just choose...
Line 249 is set to d. when you turn it to r it will post out with the cut depth that was entered but when you use D it is wrong? my lathe needs to be in Diameter
Fanuc 10 T , I have worked on it for a month to get it were it outputs everything my lathe needs. I just cant get this one figured out? you can draw a part create the code in canned cycle and it will...
Hello, does anybody know how to get separate moves to stop cutting double depth? if you use canned cycles it cuts the depth that is entered? Thanks
It uses single line. I have not tried it on the lathe yet I have been hand programing it. I just started using v24 lathe and trying to get it to work
Hello All, I just started using v24 lathe have had bobcad since 19 but just got the lathe part off it, I can not get it to use canned cycles? also in the lathe set up under cutting conditions...
Hello jrmach, thank you for the file it fixed the problem. Thank You Very Much
Hello, I had to re-install v23 after computer problem now when I go to try and use MillEditPost to enter all the information it will not open it had error MillEditPost.exe-Unable To Locate Component ...
It does not matter if I draw a new part or try to use a file from the last 4 years it still will not work. work up till yesterday?
It still will shut down using points, I can use v23 and works fine it is like the hole wizard in v24 is broke. I have reloaded the software redown loaded the service update still will not work. I use...
Thanks for the file, it will run fine the way it was sent, but when I try to have a second drill on the same circle it shuts down? I have found if I skip the geometry in the ole wizard set up...
Build 546 you can open bobcad just draw a circle go to hole wizard to do any tool go to select geometry and it will crash? also go to Cam Part milling tools try to insert tools it will crash
Hello All, every time I select geometry in the hole wizard it crashes? Any Ideas? Thanks
Hello, I just got a 1987 Daewoo Puma 8 lathe I know how to program the tail stock with the M codes my question is I have a part that is shorter than what the distance is between the chuck and the...
Hello, I sent you a private message
Hello all, I have set my machine to the KTK service class notes and now the MTI-1 board will work when i do a tool change, but when I just let the spindle run for about a hour and try to do a tool...
I noticed on my new MTI-1 card the two resistors numbers R11 and R12 are 330 ohms 5 watts on the old board they are 150 ohms 5 watts would this cause the problems?
I noticed on my new MTI-1 card the two resistors numbers R11 and R12 are 330 ohms 5 watts on the old board they are 150 ohms 5 watts would this cause the problems?
The MTI-1 board works perfect with m3,m4,m5 command but after you call m6 or m25 after the quill retracts and the spindle cuts off for you to do a tool change when you go to start the machine back up...
Hello PM sent Thanks
When my machine tool changes when I use m25 or m6 the mti-1 board will not come back on with out me pulling one of the fuses out of the board ? It is a new board and the machine has a new spindle...
Help
Hello, I have a new MTI-1 card and new motor installed when I do a tool change m25 or m6 machine cutts off then when I go to start back up the MTI-1 card will not come back on with out me pully one...
Hi all, does anybody know were I can get a used one or have a spindle motor for this machine? it is a sicmemotori
Mark I sent you a PM, and the fuses are good. Thanks