This is the ATC that I just purchased, based on several others also buying it and integrating
it into other systems...hard to even purchase all of the materials for the cost.
...
Type: Posts; User: PrestonSMA
This is the ATC that I just purchased, based on several others also buying it and integrating
it into other systems...hard to even purchase all of the materials for the cost.
...
One thing that you Really want to be able to do for a Mirror Figuring machine
is to be able to Stroke off Center...Currently you are Stroking Center over Center.
You want to be able to Offset the...
I for one would not be using Aluminum for the Framework...
It has 2 times the Coefficient of Thermal Expansion as Steel or Iron.
Thus, with any temperature changes of the machine...it is going...
My Brown and Sharpe 10 x 20 cylinder grinder says the same thing and I am hooked up to
220 3 phase power here in Mexico...often, only getting 200 volts and every thing works fine.
Your mains...
You are in This Area as it is for ATC's...
Best Regards,
Preston
Sounds Great Subnoize...looking forward to the video and getting everything working...
For me the Dust Shield would only be used when cutting Particle Board on the CNC router...the Hurco
would...
Hola Subnoize, I will be converting all of my machines control systems to Centroid and Trashing Mach3/4 as I not
longer have time to Play Around...I need a Professional Control and not something...
Add me to those interested in you Open Sourcing as much as possible.
I have a Hurco Bed Mill that I converted and would like to do an ATC,
and it looks like you have done things quite nicely so...
Ok, found the problem...
2-8 is open vs 1-4 and 3-6 have 7.1 ohms resistance.
Best Regards,
Preston
Hello Everyone,
I purchased a Cincinatti #2 Tool and Cutter Grinder on Ebay and have just hooked
it up...nothing.
I checked first to determine that it was wired for Low Voltage 220 3 phase
...
Hola Gerry,
Using the parallel port and someone on another forum said to check the box in General Conf to
"Home Slave with Master Axis" and now everything is working fine...
Thanks for the...
Hello Everyone,
Well after chasing my tail around trying to debug another problem, I am finally
back to trying to home this machine.
X, Y and Z axis work when using the MPG or entering G Code...
Hello Everyone,
I have been running the Omiocnc with a newly made control box with PMDX components.
I have copied the working existing XML file and put it into the Mach3 file area holding
the...
Ok Gerry, I did not know that one needs to restart Mach after each change in the config.
Yes, I can move the x and y with the arrow keys. Up and down, left and right.
Will try restarting after...
Ok, my error in converting the measured 0.194 inches to mm.
It should be very close to 5mm, so as stated in the Omiocnc.com specs.
Units in the Mach config page set to "mm"
However, when I...
No belt, they are all direct drive.
This is what is throughing me, as the web site
for the Omio 60/40 says that these are 5mm ball screws.
Best Regards,
Preston
Ok Guys,
A bit more confused as when measuring the actual travel of the x,y & z axises
I get a measurement of about 0.192-0.194 inches or about 0.75mm per
revolution of stepper motors.
This...
Thanks Gerry!!! Looks like I have something in the Config file wrong then.
Best Regards,
Preston
Ok, we have the machine basically functioning...
But, the units of movement are not understood.
Ie, what does the DRO show? mm or inches in
the normal mode with the "Lock DRO" unchecked
in the...