I also have a 0M-C that is acting strange. It won't allow me to edit any programs. The CAP soft key doesn't show up or the program list. I should be able to see the list of programs and hit "search"...
Type: Posts; User: riley1540
I also have a 0M-C that is acting strange. It won't allow me to edit any programs. The CAP soft key doesn't show up or the program list. I should be able to see the list of programs and hit "search"...
Hi All,
I have a 98' Mazak FJV25 with a 21 position tool changer. The changer is controlled with a Yaskawa Juspoint III model CIMR JP3. I need to figure out how to make minor rotational adjustment...
Anyone interested in a complete lab volt 5400 machine? Been sitting on a table with a sheet over it for a few years. Thought I would convert it to Mach 3 one day but that will probably never happen....
Anyone know how to enable the test button on a T32 control? I get a "BLUE #442 DATA RENEWAL NOT ALLOWED" alarm when I press the test button. Is this just a parameter issue? I've been told that it was...
So I'm a little stumped on left hand threading holders. I'm running a Mazak QT8 and I run right hand holders upside down and thread towards the spindle, both ID and OD. A left hand holder for OD work...
I'm looking for some input on a rotary axis. One of my machines has an SMW RT that pulls 3J collets pneumatically and another that has a Nikken 202 with a face plate that I switch between 3 jaw, 4...
Got them from ATS
13579 Service code
18099 setup code
Long story short....running longer than usual part, didn't modify 9999 bar change program to move Z enough and the slug got jammed when the pusher tried to clear the liner for the next bar. Unit is...
48k is all that is possible until the 34H and 34L sockets get NEC D4361C-55L chips. I'm looking for those now and should be able to expand to 128k with this 0-MB after they are installed. I will...
I went ahead and put chips in all memory locations except 34H and 34L and can only get 48k of memory with this 0-MB master board. Anybody know for sure what the 34H and 34L sockets are for and what...
So on the 0M-C machine I added four chips and turned on 128k no problem. No parity issues at all. Reloaded ATC programs and I'm off and running. On the other machine which is a 0M-B there are chips...
So I have checked another machine and multiple bits are set to enable memory. The second machine I looked at had three bits set and 32k. Other machine has two bits set and 16k of working memory. One...
D43256C-12L are the chips in my machine. my 901.4 and 901.3 are both 1.
Nice work! What sockets were empty on your machine? I have chips in 1H,1L,2H,2L and only 16k of memory....can that be right?
Well..... that explains it then. I was trying to use a 0M-B machine to run this. Thank you STLMachinist! I will try it with G54.1 P1-G54.1 P10.....or move it to another unit. Code works on newer...
Searching around and found this thread about using G52. When programming a G52 on my 0M control I get a #10 alarm.....no such G code. I am machining the same part 10 times on a fixture and was hoping...
Does anyone know what the real changes are between 0MA,B,C, and D controls? I'm running an 1989 0M-B and was looking at a 1995 unit with a 0M-C control and wondered what the real difference is....
i would like to just take a minute to thank everyone that helped me out with helpful input on this 4th axis install. Just burned a set of Rom chips installed and tested everything out.....works...
I tried that but it complains about the computer being 64 bit and won't start fladder.
Well, i'm getting closer to doing just that. I've tried a number of combinations and found that a windows xp virtual inside a windows 7 machine runs the fladder without the garbled screen. I can...
I got my hands on a Fanuc FA Writer and Fladder software from a local company. They are lending me the equipment but I'm in need of some guidance on how to go about reading ladder chips and making...
So after a number of days reading about this issue it looks like the only way to fix this issue is to alter the ladder file. From what I can tell I would need to pull the OE1 and OE2 chips (they are...
I can't seem to find anything about the yellow box as far as documentation. I'll check out the link.
The link has nothing to do with this as far as I can tell.
yes, that is correct a yellow box that says custom macro. I also have macro B option if that helps.
Maybe this is a silly question but is it possible to have a macro change something in the PMC? Can't I run a macro that would make F128.3 a 1? I don't know anything about macros much less writing one...
All is good, was missing a chip for the fourth axis control on the main board. Put that baby in and all is well......almost. Now I need some help with using a A02B-0098-C199 ladder editing cassette....
I just ordered B-55193E programming manual PC-K/L/M from Fanuc but won't have it till next week.....anyone have a digital copy they could kindly send my way?
Anyone know how to test a A06B-6058-H004 amp? The old book that I have says to test between pins that I don't have. I am getting an HCAL alarm and the flow chart gets me to "test transistor module"...
Does anyone have a complete list of motor numbers that would be entered into parameter 8420 for the fourth axis? My 0M-B book has an incomplete list. The motors in my machine are 5S with a 32 in...
Looking like a no go for ladder on the 0M-B. The A axis readout just counts away at 2.4 IPM......why would this be?