Are you still looking for vendor?
Type: Posts; User: krfrea
Are you still looking for vendor?
Control is a Fanuc 10TE
I also checked the counters page and since I cheated the sensor it is reading tool number 1 even though I removed the cheat and the sensor is not met.
Ok so I must not have cheated the tool 1 position sensor well enough the first time because I did it again this time "correctly" and since the turret was already clamped I got a solid green light. ...
One more thing, when I view the counters page, line 20 C76 reads 0 for both the preset value and the current value. From what I read this is correct after a memory reset but I thought I would let...
I really appreciate any help I can get on this, I am very familular with newer mills and lathes but I am a little lost on this one.
To start, since I recieved the lathe there was a memory error...
I totally agree with Tim.
I think if you are going to make pulleys you should use a lathe.
I think once you zero return you can no longer manually move it.
Please remember that you will be using air to blow chips etc. off your parts as you remove them besides the air the cnc uses. I have a Sharp SV2412 and use a 220 volt 2 cylinder 5 hp commercial...
I turn my standard grease-gun tip down to fit...no problem.
how do I tell what is the X axis servo unit? Sorry for the lack of knowledge.
what do you mean "in the drive"? Where?
I am getting an Alarm Code "SV013 X Improper V-Ready Off". Book says Check for a 100vac between terminal 3 and 4. Check fuse breaker is not tripped. Can anyone help me out here...where are terminal...
I have been using the .490 for 2 years now with no problems at all.
I right the programs on my computer and the transfer them to the machine via the card slot in the back door of the 2412. I would like to have a card slot or usb plug in the fornt of the machine. Is...
I have a pdf of the oi mate manual if you want I could email it to you, I would post it but not sure how to do that.
I am not sure of the mechanics on the 2412 but I can tell you that mine stopped on two different occasions, both time it was tapping a 10-24 hole and never broke the tap. I love my 2412...
longcut, I have had my 2412 for a year now and have not been able to find where to read the spindle torque...can you help me out please.
I moved my rpc to a dog house behind my shop...best thing I did in a long time:)
I will be going less than 100 feet so I think I will get some ends and try it.
I want to hook up my cnc mill to my office computer via RS232. They are in different buildings so it would be hard to pull new cables but I have a cat 5 cable I am not using...will this work for...
Thank you guys for all your help. I managed to get the holes done and they came out perfect. When I get time I plan on using the changes and ideas from you and writing a program so when I need a hole...
Thanks for your help. I have used the circle milling program mentioned above and wrote the following main and sub program. Any comments would be appreciated.
%
O0001
(1" INGERSOL DRILL) ...
need code to mill a hole 1.22" in dia., in .750 Hot roll plate, located X6.375Y-3.5 using a .50 carbide end mill S2200F4.0. I will start by drilling a 1" hole.
Thank You in advance for any help
I am still learning, I guess I do not need dnc software. I talked with a very helpful guy from Port CNC at the machine show in Milwaukee and he advised me to set up a server using "freeFTPd", which I...
looks like a nice piece of work there!
I have a Sharp 2412 with Fanuc 0i Mate MB, there is a rs232 & a cat 5 connection, I would like to use the cat 5 as I am already wired for this. I have hooked it up but it does not show up on my...
Thank you, I should of found that myself...not having a good day. Thanks again.
THE PROBLEM IS AT LINE N320...SPINDLE COMES DOWN TO Z0.1 AS IT SHOULD THEN PROCEEDS TO DRILL IN RADID...NOT THE F4.5. wHAT AM i DOING WRONG???
%
O3017(STOP FINGER BLOCK)
N5...
I have had my 2412 for a couple months now an think it is great. I am ready to try to hook it up to my network but don't no how to set up the perimeters and the manuals are Greek to me. Does anyone...