Is that Heidenhain language? I use VisualMill with a TNC2500 (Series 1 Interact), the TNC is set in ISO mode, so takes ISO-formatted POST (programs are a running list of line numbers with g,m, x, y,...
Type: Posts; User: xxcar2
Is that Heidenhain language? I use VisualMill with a TNC2500 (Series 1 Interact), the TNC is set in ISO mode, so takes ISO-formatted POST (programs are a running list of line numbers with g,m, x, y,...
I have a Series 1 Interact (TNC2500); it was full of a couple of inches of way oil with fine chips on the bottom (even though the machine was almost like new)--it's probably way oil, if it feels like...
Gents; posted artworks for making a printable mylar overlay here:
http://www.cnczone.com/forums/bridgeport-hardinge-mills/282174-heidenhain-tnc-iso-keypad-overlay-artwork.html
Cheers, Charles
If anyone is needs the elusive TNC ISO keypad overlay, attached are several PDF artworks (positive and negative, and mirror images). The one in the photo is laser-cut but the artworks are easily cut...
Mystery of ability to abort program solved: If the TNC is in ISO mode (which is the program format I uploaded to the TNC), the keys are transposed per the diagrams in the manual for the ISO mode...
Gus, thanks again.
Program running, press cycle stop button, cycle start button flashing, asterisk is flashing on display, can continue to resume/stop program. Pressing "Stop" button on the TNC...
Gus, Thank you for the reply. This still doesn't seem to work (although the manual also says it should). With a program running, or paused with cycle stop button (green cycle start blinking), the...
OK, I feel stupid. I'm using a Bridgeport Series 1 Interact, and have been able to download and execute a few basic programs from Visualmill.
I've been unable to figure out how to exit/abort a...
Hello,
I have a BPT Series 1 interact with Heidenhain TNC2500 controller. I'm using VisualMill 2012 and am attempting to get the POST debugged. I've looked through all the Heidenhain manuals...
Internal Server Error
The server encountered an internal error or misconfiguration and was unable to complete your request.
Please contact the server administrator, [email protected] and...
Machine Parameter For Bridgeport Series I Interact Heidenhain TNC 2500.
Software versions in title header of spreadsheet
Thanks for all the good info here.
gus and george, thanks for the replies and suggestions. I wrapped a band heater around the quill and heated it up to about 70C for a day or so, and stuck the hotair gun in the head again. I haven't...
Hello All,
I've been lurking on the forum for some time, and thanks to everyone for all of the great information.
I recently purchased a Series 1 Interact with TNC2500 control, vari-speed pully. ...
Jason,
Thanks for the reply and help. That sounds very reasonable.
Thanks again everyone for your time and help.
Charles
DC,
Thank you. I havent hooked up any external keyboard, but I'm pretty sure that it is not going through ANY bootup or post (starts beeping immediately). I've hooked up an external display...
Hello Gentlemen,
Jason and Kurts and all, thanks again for your time and response and sorry for the delay in replying.
Jason, I definintely think it is either the motherboard, (or one of the...
Gentlemen,
Thanks again for your input and help:
JP, I did take the front panel off and plug in a separate VGA monitor--no activity still.
CNC and DC, this machine has an "upgraded" PC has a...
Thanks everyone for the input.
I have not tried to plug in another monitor yet. I assume this uses a standard VGA cable that may be plugged into the PC? I was looking at the schematics and it's...
Hello All,
I would appreciate any help and/or recommendation on what to look for for the following problem:
Machine is Milltronics Partner 1, 1995 series J (SN 3409), factory refurbished, 10k...