Search:

Good Day, It's Saturday so I cannot call LNS so I'm trying this. I'm getting an alarm "Positioning Stop Proximity Switch B5 Signal Faulty" In the manual I cannot even locate a B5 switch. They mention...

We have three of them. We like them. We don't have the exact model you are referring to though.

I crashed the turret into the collet chuck. Machine was setting still when this happened, but it was a pretty good knock. I had to realign the turret rotation. However now the Z home position...

We have a new DNM 400 and the code was wrong on the program for rigid tapping I get a 2210 error. The manual says to do a "tapping retract" There is a button for this, but how do I do it? Thanks

I have a very similar issue on a Lynx 220. Our Doosan tech send me an adjustment procedure to align the arm. We had actually had the arm down and crashed a tool into it. You can pretty much...

Does anyone here know of a source for ID toolholders for our Doosan lathes? Our Lynx 220 LM has a BMT 45 turret. I need at least one new ID toolholder. The only place I can find them is through...

that's it....confirmed

Sounds Great! Where can I order it?

It is: ML0027-001394 Thank you

That is the one I have..........301308-00287. The problem I have is that Doosan distributor wants over $800 USD for it. Do you want serial number off of the lathe?

can they be repaired?

So I crashed the tool setter probe on the Lynx 220. It damaged the top button on the probe part. I have checked into getting a new one and they are $800 plus just for the part. Does anyone know if...

You talking of the VMC machines? We have had a DNM 500 for close to three years with no issues. It's pretty much a bullet proof machine.

You might try the Gibbscam forum. My experience is it gets a bit complex getting machine simulation working. If you could get back into maintenance that would be a big help to you.

Has anyone had much success running Gibbscam or a similar software on a Mac Mini? I am especially concerned about the graphics end of it. I realize I will need to run Parallels to run a windows...

Ok, so Saturday morning and have a problem on Doosan Lynx 220LM. When control gets to M35 to activate C axis nothing happens. The green cycle start light stays lit and machine just sits there. ...

may have to explain more............I am not seeing extra circles. Also try the Gibbscam forum at Gibbscam.com. You will get a good response there

Just getting our LNS QuikLoad up and running here. I have a question............Where exactly should I be setting the top cut position? In front of the chuck? How far behind the collet pads should...

thanks!

We have our new Lynx 220LM up and running now. I am going to write my first live tooling program on it tomorrow. I have written a couple for a Haas lathe with live tooling, but never for this...

I have a bar pull program going. At the end of the program I have an M99 so that it loops back up to the start. However I want to loop back up and start at block N200 not at the very beginning of the...

We purchased a used Clausing Startrite H250A automatic bandsaw that was supposedly rebuilt. It is working well except for: The saw head wants to creep down and the downward feed can be quite erratic....

A very simple way it to go to your solids pallate and go int advanced solid modeling and choose the shell/offset icon and extend you face that way.

Basically the other machines I am familiar with are Okumas and Moris and there seems to be difference in how hard we can run them and reliability compared to Haas. That said I realize Haas has...

I do contract programming. Two of the main companies I work for have been Haas shops. Right now both of them probably will never purchase another Haas. There have been just too many breakdowns...

The Haas machines are good? Not too sure about that one

Your clearance diameter will need to be larger than your tool diameter and smaller than the hole size. Also post this question or do a search at GibbsCAM Support Forums - Powered by vBulletin. You...

Are you using a later version of Gibbs? If so select the surface then right click. A extract geometry box will pop up, or in the geometry pallete there is an icon that is shaped like a box. This...

Yes, you can put geometry around the outside of your raw stock and call that an air wall. Then geometry around your parts shape and that will not be air but a blue contour. Also you can try 3D...

I am not sure that you can upload vnc files here on this forum. Go to GibbsCAM Support Forums - Powered by vBulletin and register and upload your file there. I believe you find someone to help you...