How many times the red flashes in each cycle? if it is 7 times, it means position following error, indicating that there is a problem with the encoder feedback signal.
Potential reasons?
1. The...
Type: Posts; User: Leadshine
How many times the red flashes in each cycle? if it is 7 times, it means position following error, indicating that there is a problem with the encoder feedback signal.
Potential reasons?
1. The...
Hello, according to my experience, this may be caused by the damage of the internal module?s?.
Please contact your direct supplier to deal with or replace the module.
Hi Jacques, I replied your email before, as below...
I checked your spindle DDBLDV 1.0 manual that it can be controlled by external analog input as motor speed control.
However, its voltage 5V...
Hello,Please let me know the model and serial number of your drive?
CS series is designed for overseas customers so it's not released in China market there is no English manual and software on...
Hello, this is Jason Peng from Leadshine, It seems I had replied your this problem by email,please check. thanks.
Hi Gantarone,
For the control signal,there is strict time sequence to make sure the drive can recognize signal correctly. PS:Different drivers have different timing requirements
Usually, the DIR...
Hi Shane,
Thank you for supporting Automation Direct.
It seems that the drive DM860E does not receive the normal pulse/dir signal please check if there was any correct 5v pulse signal output from...
Hi Luke,
Thank you for supporting Leadshine products.
The motor CS-M21708 is rated 2.5A, you need a tuning cable to set a smaller current in CS-D508 to avoid motor too hot.
Please try to contact...
Hi Digdagdigedag,
Thank you for sharing us the experience on using Centroid controller and drive connection. Your comments are appropriate and reasonable.
Actually, the logic signal current...
Hi ManjuHBR, thank you for supporting Leadshine products.
The motor phase UVW must be corrected to the drive LD5, do you have motor datasheet and where did you buy the low voltage servo drive...
Hi Digdagdigedag, thank you for helping us.
YES, we need to know how LMEB83 connects this 12v power supply signal as a pulse/direction signal input. It is likely that the single-ended signal input...
How do you connect this 12V to the pulse and direction signal? whether there is correct pulse signal output to the drive.
The MX4660 schematic is not released, there is a channel to output analog signal to control VFD. Refer to page19 http://www.leadshine.com/UploadFile/Down/MX4660d_V1.2.pdf
PIN14 for PWM on DB25,...
First of all, I'd like to know what model of new motor you have changed? If you have used Leadshine encoder extension cable ? I think there are some problem with encoder signal transmiting between...
Hi Ron,
Thank you for your attention on Leadshine products.
Err020 means position following error. Our default setting is 1000 pulses in the software. If the error value of encoder feedback exceeds...
Hi,Garry
I am John ,an application engineer from Leadshine.
Can you send me your wiring diagram of DM320C to Breakout board ?
Actually ,there are many factors cause the drive not working.from...
Hi
This is a common issue for MX3660 AND MX4660 , the IC has 1.1V oltage drop ,so that the output is not 10VDC
I am sorry for that ,and we don't have solution for that .
John
Leashine
Hello
Both ES-D /ES-M and HBS/HBM are from Leadshine . but ES-D /ES-M is special for oversea market .HBS for domestic market .
Some Chinese trading company sell HBS too .but no technical support...
Do you mean something for stall sensing of drive ?
I don't know how to attach the files here .but if anybody want this file , please email me directly .
[email protected]
John
Application engineer
Leadshine
I am JOHN ,an application engineer from Leadshine
We have a document special for shunt regulator and capacitor information .
Would you mind telling your email , i can email you this document
...
Dear Sir
Thanks for you would like to use Leadshine products !
Base on your motor information , i recommend you to use Leadshine DM870 or DMA860H.the below link is DM870 details
Leadshine...
Hi Kmin
The peak current =1.3*RMS ,normally ,we set RMS for the motor
For your motor 1 ,PK299-E4.5A ,and if the connection type is parallel ,the current setting on DM860 should be 6.00A -----...
Hi Donny
I have replied your email .
John
Application engineer
Leadshine
Hi
DM542 is not Discontinued,but we have not released it on our website ,you can buy it from leadshine directly or leadhsine distributor .
Are you in USA ? if so ,you can buy from Leadshine...
Hi
For DM856 ,the Max input pulse frequency is 200Khz .
You can set the Kernel speed just base on your machine working speed and the micro step setting .
Hi
Please read the user manual Figure 18 ,MX3660 connection diagram .
There is diagram for 4th aixs .
Hi
It is possible to add one axis on MX3660 ,but this axis is different from other axes ,the speed is limit .the Max output pulse frequency is about 20Khz.
You can download the updated user...
Hi
No need set the serial port configuration settings ,the default is ok .
PLease send me some screenshots ,let me check it
Hi Bryan
The DB25 cable is standard parallel cable for printer , i think you can find it from your market .
286032
The cable for motor is not necessary to buy a shielded cable ,the normal one is...