Check the OSC frecuency (pin23)
Oscillation frequency fOSC WITH External resistance Rosc = 51 kΩ
Min 2.8 MHz
Typ. 4 MHz
Max 5.2 MHz
Type: Posts; User: riphet
Check the OSC frecuency (pin23)
Oscillation frequency fOSC WITH External resistance Rosc = 51 kΩ
Min 2.8 MHz
Typ. 4 MHz
Max 5.2 MHz
I've seen the diagnostic screen.
I have verified the performance of each signal separately.
Clearly I have Mach3 should work with the X, Z just as "Y". That's what not occur.
Some postings...
Hello,
I'm a newbie, using the demo version R3.043.066
I'm wiring a CNC machine limit switches.
The machine is three-axis.
The X axis with one motor
The Y axis with two motors (A slave)
The Z...
Changing the order of the factors does not change the product.
So, what's the point?
So, you deny that there is a Back EMF?
And denies that the energy of this "spike" can be sent to another...
Excellent,
I have no instrument to measure peaks.
Anyone have any examples of measurements in IC toshiba drives,
with and without diodes diodes?
(TB6560 and TB6600)
The data sheets do...
The question is:
On "step zero", What is the state of transitors?
How I can check?
Yes, it is that you only refers to the heat generated by the IC.
Ignoring kickback , which is to cut the power to the coil.
As explained above, this can reach over 42Kv. the example presented.
...
I can I respect you, that:
You think anything is irrelevant and insignificant,
I do not approve but I respect it, so be it for you.
You should be powerful, capable of despising anything.
You...
At this time, no more eBay tb6600 drives for sale.
If I needed a driver now,
without hesitation,
this is the buy.
I would order only sold me with "diodes includeded" option :) ,
for...
Indeed in the datasheet is written:
"Note: Parasitic diodes are indicated on the designed lines. However, these are not normally used in Mixed Decay mode. "
"As shown in the figure above, an...
In the datasheet TB6560 or TB6600:
I do not see, if the IC has included (buildin) the diodes.
THB6064 included buildin the diodes?
Why would anyone in their h-bridge design include diodes?
...
Lo que hagas con tu miserable vida no me interesa,
Este hilo de conversación se inició con una pregunta relacionada sobre "DOS MOTORES DE PASO EN UN EJE".
Estoy empezando a cuestionarme:
¿Por...
I appreciate your time and attention given this.
I bought it and I'm waiting for the shipping.
I'm no expert in electronics,
probably I can not straighten the chip.
But I can change the...
No me preocupo, ¿Por que?, ¿Tendría que preocuparme?.
Como "buen predicardor", ahora me conminas a que yo me arrepienta,
pero no tengo necesidad como tu de arrepentirme.
La respuesta a mis...
Evidentemente si hay más predicadores.
En mi caso no requiero invertir el sentido del giro del motor A,
Valoro tu sugerencia, gracias.
Amplias mi sospecha respecto a la configuración de Mach3,...
Si tienes alguna culpa, quedate con ella, yo no te disculpo.
(¿en que lugar se habla sobre de la culpa, disculpa y arrepentimiento?)
La creencia de Roque7 es que "no le pregunte" -sic-
Las...
No respetas al foro ni al hilo que inicié.
Además de hacerte el ofendido y sugerir que me enojo,
Cuando en realidad provocas que te humillen,
(Es tu necesidad de "valer la pena").
A saber,...
I see the Toshiba TB6600 Stepping Motor Driver Board.
Ebay item 170923696690
Someone used this?
What experiences have on?
I would like to know your comments on this drive.
Document:...
The datasheet is not everything.
I found TB6560AHQ File Usage Considerations.
Motor power voltage (Operating range)
4.5 V to 34.0 V
I found the file Reliability Information.
Reliability...
españolingléscriollo haitianoAlpha
When I read that ic 40VDC, 3amp. So the idea I have is to be able to work with engine power up to 120 watts. I suspect that it is not reality.
My question now...
Search "FANUC" on the www.ebay.com
Just to clarify
The TB6560 you say you do not know, is this.
... and say 36V.
I appreciate your time and attention.
Eres el unico sacerdote en el foro que responde con creencias o hay más ???
Aprecio tu tiempo y atención.
Si tengo otras opciones, pero esa es otra historia.
Pero sigues sin explicarte DONDE realizar la conección en paralelo que mencionas.
No es clara tu respuesta, donde sugieres puentear ???
Me pregunto si así tienes puenteada alguna maquina CNC ???
Tienes idea de los requerimientos de los sensores de señal ???
I see several topics about Chinese board TB6560.
But still not clear to me that occurs with top voltage (36V)
1.- 36VDC exactly happens?
2.- Then what is the maximum voltage to work fine?
...
Hello,
Building machine with 3 axis, the Y axis need two twin motors.
Then need equal signal by each motor.
Ports and Pins, Motor Outputs:
I try write double Pin# writing with sintax:
Y...
In a THREE Axis CNC machine X, Y, Z.
With Chinese TB6560 board FOUR axis (with parallel port).
Controlled with the Mach3 software
I wonder what is the best settings to wheel two stepper motors...
En una maquina CNC de TRES ejes X,Y,Z.
Con una tarjeta china TB6560 de CUATRO ejes (puerto paralelo).
Controlada con el software Mach3
Me pregunto cual es la mejor configuracion para hacer...