Have you sold this?
Type: Posts; User: hollisin
Have you sold this?
This helped me with my estop problem
Thanks
Steve,
my homing settings are
X 20pct of 750 = 150, air gap is 1/16
Y 10pct of 750 = 75, air gap is 1/16
Z 60pct of 31 = 18, air gap is 1/8
Haven't checked it in a while but was only .001...
I this still open?
Al
Do you have some examples or suggestions about how to use 24 V input and output signals.
It would seem that powering electronic switches with 24 V would be possible. If the inputs are just...
Thanks Gerry
It was electrical noise.
Long story version follows
when I attached the Hall first switch I connected it directly to the bob. Worked great. I was also looking at wiring...
I finally got it to work perfectly I will post a update after I get back from dinner
Thanks Gerry
I have shielded cable with the shield grounded in the control box.
I have one of those choke coils at the switch.
I have a Y5U 104M capacitor from the 5v to ground. Without this it...
Does anybody know how to set the retract after the switch has been activated. About half the time mine just stop and the switch remains activated. When it does this it stops and will not home the...
They will list another like this if you email them. This what I have done.
I Check that the ground on the board was the same as the ground of the case Before I connected them.
They will make a...
I purchased these and removed the 4 way jumper. I wired my 5 volt supply for my limit switches and the inputs using this. Much easier than using the connectors on the bob.
They are willing to set...
I will preface what I say with this thought. If you do something and it works, it does not mean its the best approach.
Using a ground wire for signal or power current is really at the top of the...
kolias who is the member you got the picture from? I would like to ask him about the connectors in the top of the cabinet and the mother board.
Thanks
Jack
Thanks for the info about the heat shrink tubing that will be very helpful.
These are some photos of the completed bracket. The round disc has the magnet inside it. I just cut it out with a plug...
Lucas,
Is it possible in the future you'll be analyzing and/or constructing some DSP-based drivers?
Jack
Thanks for everyone's help.
Please see my current version in the attached pictures. The magnet is the little round thing in the white plastic it's 3 mm. There is an empty hole beside it I used a...
Finally got the circuit in post 964 wired up to a perfboard and connected it to my hobby CNC controller board. Tried a few different things to verify that it was working none of which worked. Finally...
Turns out I have a hobby CMC board not a xylotec. Above the 11 12 13 and 15 connectors there if there's a screened sentence that says pulled up with 10K (RNS). The home and limit switches were wired...
Lucas,
What is your goal for purchasing and analyzing this? Just curious.
Jack
Rick,
I looked at your build thread and I ordered some of those deans connectors might give them a try since they're so small and it looks like they're an ideal fit for this project
Thanks
Jack
Thanks everybody you've been a big help.
I have an old Zylotec Hobbie CNC board. And mechanical limit switches now. I have a switch wired up and it looks exactly like the first picture from John....
Sir,
I have been trying to follow this thread since the beginning and am having a difficult time. I have purchased the components and have a circuit working like the one that's pictured on page 77...
Would one of the electronics experts on this thread compare the two stepper drivers below and tell me which is better and why. I am in the process of upgrading my CNC controller to discrete...
Did this ever happen??
Thanks
I have a url for a page on the www.cncecke.com web site. It is not letting any new users apply. I need someone to tell me what is on the page. I think its about how to construct a cnc pendant.
...
So how much are the plans??
I am trying to reproduce this machines capabilities.
Would you post your machine specs and some pics.
List of software would also be helpfule.
Thanks Jack
Legacy CNC Woodworking -...
I have a hobby cnc pro board working. I am looking for a schematic for the board.
Thanks