Your right I wasn’t considering buffering of the gcode
The main reason to try and implement DistToGo is for proofing out a programs where clearance is an issue.
Ya it wouldn’t be useful for...
Type: Posts; User: dirtdigger257
Your right I wasn’t considering buffering of the gcode
The main reason to try and implement DistToGo is for proofing out a programs where clearance is an issue.
Ya it wouldn’t be useful for...
What are the first 200 persist.userdata variables
Is there a list some where
I’ve searched through most of the kmotion434 files
And can’t find them.
I'm try to make a distance to go dro...
My machine is a Novakon NM200 3 axis mill.
I was using a hiemer 3D Touch probe and dial test indicator
Checking x and y from the solid jaw of my vise it has a smooth surface ground finish.
I...
Does anyone know when backlash compensation is used by the G code interpreter?
My problem was when adjusting backlash settings in my init program I could see the changes when jogging the respective...
Thanks works great
Is it ok to have two for loops running in separate threads
one in my init the for the MPG
the other for servicing KmotioCNC jog rate and tool offset?
If not it take to...
Hello everyone I am trying to implement a button to turn tool length compensation on and off or at the least a Led to see the status.
Only thing I can think of is to monitor the variables for...
G90 works better for any type of movement you want to do,
It doesn't work better for incremental moves
if you forget to cancel the G91 you will crash
This was just an example I know how to...
[QUOTE=TomKerekes;2062730]Hi dirtdigger257,
What do you mean "omit]
I mean it ignores it ,it should work in with G90 Or G91
I'm making some linear test cut with different feed rates and rpms
O100
G0 X0 Y0
Y.1
Z-.75
G1 f50 x-4
G0 z1
G91 G10 l2 P2 Y0 (shifts the y axis 0.1)
M99
I'm running kmotioncnc and can't get the interpreter to omit a G91.
Example G91 G10 L2 P2 X0 Y0.1
Would the answer be changing something in the
Tool setup screen -> tool/setup files-> setup file?
I'm running kmotioncnc and can't get the interpreter to omit a G91.
Example G91 G10 L2 P2 X0 Y0.1
Would the answer be changing something in the
Tool setup screen -> tool/setup files-> setup file?
I've been doing some 4 axis machining and was wonder if I could creat a c program that would do something similar to haas's G254 DWO?
I've been doing some 4 axis machining and was wonder if I could creat a c program that would do something similar to haas's G254 DWO?
I've recently upgraded a novakon nm200 to kflop and having trouble with rigid tapping.
I seems everything is working as it should the ratio seems rite. If i set z zero on the top of the part ...
I reacanlty coverted a nm200 to kflop and am having trouble with rigid tapping. I'am using mach3. I would like to start a new thread but cant seem to figure it out on my phone. I moved into a new...
Hey wizbang thats doesnt seem all that bad to me( the head deflection). I just bought a nm200v2 today and its in pieces do you know where to find a manual for it mainly wiring scematics and i might...
i think i have something figured out. when i unplug the encoder from the c10 board the travel is smooth in open loop mode using mach3.
same problem i was having with the limit switches. if i plug...
221794I flashed the new version zeroed step response screen and my dial indicator it returning to zero221762
After 20 time of hitting the move button it was of by .005
221752
it is over shooting or going passed about .005 inches in open loop
221738221740
221736
my system is kl-5056d drivers set to 2000 microsteps 1/10, c10 board ,1.8 degree step angle 2 phase motors. I'm not using a filter. the p gain you referred to is that the proportional? i watch the...
221698221694221696
the encoders are .005 resolution and i'm running 2000 microstep on the driver 5mm pitch ballscrew
so 1 rev =5mm =.19685039. for 5mm of travel the encoder should be...
Thanks Al
I had the input channel set wrong i have position and command overlapping. The movement isnt as smooth as it should be i think the sample time of the driver and encoder arent messeing well so i need...
Got it picking up changes with the multimeter thanks. Now i'm tring to get tuning going the red position line is moving now but it but the spike are small compared to the command
No 0v not hooked up ground is just hooked to the c10s ground. I'm not sure where to hookup the 0v. It does make since that could be the problem.
Hi I.m try to hookup a set of Ditron DC10 linear encoder to a kflop board. I have the encoders wired up to match a pinout off of the Ditron website but I.m not getting any Voltage change when i test...
Ok, thanks. I did get all three axises working moving the proper amount and in the right direction after adding the extra setup up time. But now when i try to run with limit switches it acts funny,...
command type pul/rir or cw/ccw active edge rising or falling direction def high or low. mine is set default because i dont have the cable to tune them.
Default setting is PUL/DIR mode and rising...