I think I had that problem with one long ago. Or maybe it was an Acroloc. Way oil got low, stayed in permanent single block until cleared.
Type: Posts; User: beege
I think I had that problem with one long ago. Or maybe it was an Acroloc. Way oil got low, stayed in permanent single block until cleared.
So it doesn't like the THEN word. Did you try:
#100 = 1
#101 = 0
IF[#100 GT 5]#101=5
??
Beege
hi....
IIRC, F40. is supposed to try and move to the next place in .025 seconds. Start with F.5 (2 seconds) and see what happens. You could also put a G1 with that G93, as you're currently in G00...
Is your subroutine local (as in (DFS, L1)~~(ENS) or a separate registered program? A local program should be (CLS, L1, 99) and a separate program would be (CLS, 1, 99) where the "1" would be the...
Have you tried (CLS, L1, 99) where just 99 is the number of repeats?
Beege
The G53Z0 is NOT the problem. The problem is the G2 at the end of the program. G2 is modal (clockwise arc). Any movement command (like G53Z0 or X10.Y10.) while G2 is active, requires a valid arc or...
Hi Mark,
And welcome. I've been trying to use EC for the last 2.4 years. Long learning curve for me. Lots of options on toolpaths, less than comprehensive help files. There are some youtube vids...
I don't think you need all that repetition, as the parameters are modal.
G43 G00 Z.2
S200 M5
G84 G98 Z-.1 R.2 F10.
Z-.2
Z-.3
G80
G00 (Next hole location)
The video is NOT correct. He forgot to include a linear move to the edge of the part, at X5., then G03X4.75Y-5.0I-.25J-.25, then another linear move out of the radius in Y before moving again in X....
I'd try to specify the size of the spherical radius on the tip of your probe. .0005" may be too sharp. .010" may be too blunt. .002" could be just right, and all are measureable.
Try using M99P#### where P=N####. I used to jump around in a program using this on a Fanuc and a Yasnac. Sometimes a GOTO wasn't available, but if you have Macro B, you can use this, too.
I think you can replace your factory M06 with a Macro M call - write a sub to one of the 9000 programs listed in your parameters, assign it M06. Haven't done it, but mebbe? You have a separate M16...
Give us a sample of your program. If you're using a G92, you might experience a problem like this. G92 will take your current position and change it to the values in the your G92 line. Bad if it's...
That second afternoon break has always been a momentum buster. We went to a 20 minute morning break (with a loud buzzer on either end), and no afternoon break. Kept the half hour lunch.Same loud...
Nevermind
Good time to give Hardinge support a call. As far as activating /deactivating the bar feeder, IIRC, you press two buttons together, like "SetUp" and "Jog" (I don't remember. been a while). as far as...
Two buttons at once. Either shift-cancel or graphics cancel
You should always turn off comp with an X Y or XY move. Since you have at least 2 Z moves the computer doesn't know how to resolve the turn-off vector. Try inserting an XY move after you bring up the...
Thanks jtreanor,
I never saw the spaces there.Thanks for the enlightenment!
Showing my age... I don't think I've had my hands on an i control...
You'd have to have two or more actual block delete buttons on your control panel (or some other means of turning the switches on or off) for this to be functional. The machine tool builder would have...
I want to tweak our Haas post to remove spaces from between codes, but not inside parentheses. Anyone have experience with this? Can it be done? How?
My DNC program is set up to send the % before and after the program. If I send a program with a % already in it, I get the empty program alarm. Try sending without the %.
Definitely turn off comp with a straight line, preferably perpendicular. My Haas had a few times where the tool table got corrupted, and the machine would lock up. If fixing the program doesn't do it...
Comp #9 can compensate all around the tool, especially for a tool with greater than 180 degrees of arc. You'd set it so that the center of the cutting tool diameter is zero. For example, if your tool...
I'd be using a 9 for my comp number, driving off the center of the radius, not the edge.
T'would be nice to know where you are located...
Try changing the S5.0 to U5.0
I've never seen G04 used with an S word. Is that documented anywhere?
And at a vector feedrate of 100. The angle created would depend upon the starting point, and whether the mode used is incremental or absolute (G91 or G90)
I've thought of this recently, and have in mind three fingered overlapping jaws that bypass each other as you close the vise, effectively clamping down from inside the feature as you tighten the...