Sorry, no backup for that machine.
Type: Posts; User: GPena
Sorry, no backup for that machine.
Hello davesnd, I have a Mori AL-2, recently we had to reset the control due to a problem, we do not have a parameter backup :( so everything is losted. Do you have the PC and PMC paameter backup of...
Sorry, I culdn't get the manuals for that machine.
Good luck.
Hi, you can check on SAI CNC ? Venta de CNC you will find good stock with them, and they are in Mexico, not far from you.
Good luck!!!
Hi rkservice, do you have the manuals for this machine? We also need them. Please let me know to: [email protected]
Thank you.
Thank you very much cnzrepair, we will replace all the filters and test it.
Hi guys, I am having the same exact problem as icentropy, it began once a day but now is every 10 minutes or less, imposible to work that way!!!
Did you solve it with the power supply repair? Was...
Hi, we recently bouught a nice Conquest T42 with subspindle, unfortunatelly there are no manuals. The Fanuc manuals are no problem, but the manuals from Hardinge like operation, electrical wiring are...
Hi Bertie, I am trying to get the parameters and PC parameters for my CK-2 with Fanuc 10T controller, could you please share them? Our machine is down.
I hope you can help me.
Thank you.
Well, we finally found the problem...There is a switch in the head of the machine that selects to work the coolant in auto or manual mode, it was in auto and that is why we wasn't able to perform...
Hi, we have a CNC mil with an Allen Bradley 8400 controller, there is a problem with the control. We turn on the machine and we are able to move the axes, when we try to send the machine to "MACHINE...
Pennine in UK have some manuals in PDF, I am sure that you can download it from their web site. Pennine Automation Spares CNC Services, Fanuc Spares, Parts
Goog luck.
Hi, we have a CNC mil with an Allen Bradley 8400 controller, there is a problem with the control. We turn on the machine and we are able to move the axes, when we try to send the machine to "MACHINE...
Hi, we just bought a Mori Seiki VMC model MV-40 with Yasnak i80M control; the machine works great but we can not move the 4th axis, the digits in the absolute and relative position moves but not the...
zoik4you, if your SL-1 has a fanuc 6T-B control could you share a parameter backup?
Thank you.
Greg.
Hi,
We had a damage on the bubble memory of our SL-2 Mori Seiki lathe with fanuc 6T-B, we will replace the board but we do not have the parameter backup for that machine. If some of you have that...
Markoooo, I have the manual of the SL-2 with Fanuc 6T-B controller, if you need it I can send it to you.
Hi zoik4you, wouly you share a copy of teh manuals to my email [email protected] ??
Thank you.
getdog, pudiste solucionar tu problema? En que ciudad de Mexico estas?
Saludos.
Hi to all, we have a Leblond Makino FNC-106 with Fanuc 11M controller, we have a problem with the ATC (It alarms on tool changes), it seems that it has a separate PLC instead of the standard Fanuc...
Dali:
Check the feedback sensor that sends the feedback signal from the motor to the drive, it is located on the top of the spindle motor and it sends information of the actual motor speed to the...
okroyo,
Not all servo motors have a break, if you check the model of the motor you can see if there is a break inside seraching for that model on the web, if your motor has a break then you must...
TCSPOONER,
The third red led from top to bottom is HCAL and the fourht is OVC, both of them are alarms; the most probable thing is that the servo amplifier is bad, you can swap the one in the X or...
Hi,
We have 3 Fadal VMC's, two of them has a Toshiba inverter for the spindle and one has a baldor spindle. When we use the machines with Toshibas below 300 RPM's the overload protector trips, we...
If you have the Fanuc manuals there it says hot to make a backup. If you don't I will try to explain.
That is right Deano, 6 controls doesn't need batteries since they work with a bubble memory, so, don't worry about that. But I recommend a memory backup, it is allwys usefull when you need to...
Nakamura is a good machine, Fanuc 6 control is great for lathe applications. I would say that if the pice is right go for it...
Hi,
We have a problem with a Kitamura VMC with i80 control, it is simple but we are having a hard time to do this. The problem is that the spindle motor was dismounted and the control...
Hi, have you solved your problem ? Maybe I can help you with a backup of my machine, it has a Fanuc OTA control.
Greg.
Thank you very much dcoupar, you can send them to: [email protected]
I will be waiting for them.
Greg.