Below information is about our motor and driver
http://www.cnczone.com/forums/news-announcements/89162-come-see-mini-machine-brushless-motor-controller.html
we make 2200W motor and driver...
Type: Posts; User: Kung fu panda
Below information is about our motor and driver
http://www.cnczone.com/forums/news-announcements/89162-come-see-mini-machine-brushless-motor-controller.html
we make 2200W motor and driver...
Hi Everyone
This is our new driver 2200W 6000rpm , and 1100W 6000rpm , have bigger torque at low speed
Some people from the cnczone have use the new driver from me or from keling.
I think we...
these picture is test data
[email protected]
zhangQi
HI
you can sent message to chris to ask the test ,maybe you can see this forum,and contact with him ,i hope he is better now ,he told me he is injured,now is recovering,can not do much heavy work...
guys, I will do special suppport on the updated controller if you need. Please contact with me privately, and we can talk further.
my e-mail: [email protected]
Hi Pat
Chris is injured in a car wreck ,you can see below ,
this is his forums
Hey everyone. Just wanted to post what was going on since I haven't been out here much lately.
Motor and...
Hi
The sample i sent to USA ,Chris have test it for along time ,and he have posted some videos of running the system in steel which is more than the other controller would allow him to do. he...
hi Chris
these days we are doing some test in machine factory ,Now all have tested ,and i will sent the new driver to you this week ,and i have get your mail about you address ,i will sent them you...
this is the new driver description ,if anyone couldn't open the PDF just sent E-mail to ask for the file ,i will sent by mail to you ,thanks
zhang
my mail [email protected]
...
Hi
You can give a call to Keling,Now he is in USA
zhang
hi
keling only order 1100W 6000,and 2200w 6000rpm ,most of people like the high speed .keling didn't order the 3500rpm motor from us ,and the 3500rpm motor is more expensive than the 6000rpm...
hi
can you tell me the speed you needed ,if the speed is about 3000rpm .i think 1100W 3500rpm is enough (92#motor),if the speed is high and cut steel difficult ,i think 2200w 6000rpm is suit for...
this is the test data information at 400rpm , 800rpm 1500rpm 5000rpm ,low speed have high torque,
The picture is the field test
zhang
Hi Chris
You can order from me ,
my e-mail is [email protected]
zhang
Hi Bob
Thanks for your always support to us ,the torque is big enough ,we let a lot of people in our factory try to hold spindle,some of them are very stronger,but they couldn't stop the spindle...
Hi everyone this is the controller, both 1100W and 2200W is new ,and have high torque at low speed .
In 2011 ,we try many measure to solve the problem ,and have a very big pressure .
Today...
The 9 controller(NEW) have been sent to USA for a long time
zhang
Hi cjdavis
I promise i will give one more controller for you ,Need to wait until after the Spring Festival in China.when keling receiver the motor and controller you can get one from him,keling...
Just be sure the motor should be correctly fixed in your machine. The axis of motor must be installed vertically. If it's not in the same vertical line, motor will vibrate, and easy to be damaged.
The product performance is stable now, and we are ready for sale anytime.
Please sent them to me ,i will replace for you,sent the new dirver to you
Best regards
zhang [email protected]
We are ready to produce the new control(1100W ),Now we are preparation
2200W still need sometime ,now we drawing the circuit diagram (2200)
zhang
Everyone ,
this is the new controller ,i have attached some photos,we have change the IGBT,and do some adjust ,to make the control more strong.
zhang
[email protected]
Hi,
We have modified the software of controller, and also changed the value of transistor and capacitor.
The software modification is to prevent the new and revised board from failing. when...
Hi Journey_Man
Thank you for giving my confidence and support,now we have solve the problem.thanks
Best Regards
zhang
Hi
Thanks for your support, now we have solve the problem
Best regards
zhang
Hello everyone,
we now have solved the 4 pole motor low torque issues through software adjustment, and the torque at 400rpm is strong enough.(4 pole motor)
both 1100W 6000rpm(4pole) and 2200W...
Hello everyone,
we now have solved the 4 pole motor low torque issues through software adjustment, and the torque at 400rpm is strong enough.(4 pole motor)
both 1100W 6000(4pole) and 2200W...
1、this time we solved the problem mainly to adjustment the motor,change the motor from 4pole to 8pole,because the 4pole motor only 4 induction angle,the motor pluged when turning there is easy to...
the voltage is exchange between 110V and 220V
the power is 750W 3500rpm or 6000rpm
1100W 3500rpm or 6000rpm
1500W 3500rpm or 6000rpm
2200W ...