Thank you Mauri
but I am looking the post processor setting in Unigraphics NX8
Type: Posts; User: pcreek
Thank you Mauri
but I am looking the post processor setting in Unigraphics NX8
Hi
I need help in writing a post for my 4th axis indexing table (Chuck). I am programming in Unigraphics NX8 and tried the generic 4th axis UG post. But the 4th axis is trying to go back to zero...
Hi
I have a Nakamura Tome TMC20 and When I am facing, it leaves a pip in the center. Looks like the turret center is off. Can anyone help me to sort this problem out.
Thanks
Parm
Thanks MBI.
Any example how to write a sub program for tapping.
Thanks
Hi
Does anyone have used magnetic sensor from Fanuc. The part number is
A57L-0001-0037. This is for my Kitamura Mycenter2 milling for spindle orientation.
Thanks
Hi
When I make a simple drilling and tapping prog on my VMC Mazak with mazatrol M32 control, it gives me a following alarm.
"844 not found prog no"
"An attempt was made to call sub program which...
Hi
I am also looking fanuc magnetic sensor for my kitamura mycenter2. This is for spindle orientation. The part number is A57L-0001-0037. Pl inform where i can buy this part (new or second hand)....
Hi Eric
Thanks for the response. is it possible if you can send me the photo where it fits in your machine.
Thanks
Hi
I am running Mazak AJV18 with mazatrol M32 control. while running the machine the system disk (3.5" Floppy) is scratched and now I can not run the machine. Whenever I turn on the machine, it goes...
Hi
I have an alarm 243 spindle rpm malf on my mazak VMC with mazatrol M2 control. Any suggestions Pl.
Thanks
Hi
I am also looking the parameters of M32 mazatrol control. I have mazak AJV 18 VMC. I need a parameter for the 4th axis. Pl inform me if you have these parameters.
Thanks
Parm
Hi Parshad
If you have parameters of M32 mazatrol control can you please inform me. I need these parameters for my Mazak AJV 18 VMC for the 4th axis. My email is [email protected]
Thanks...
Hi
I need parameters of M32 Mazatrol control for my Mazak AJV18 VMC. Pl inform me if you have. my email is [email protected]
Thanks
Parm
Hi
I am also looking the parameters for my Mazak VMC AJV18 with mazatrol M32 control. If anyone can help please.
Thanks
Hi
It is kitamura mycanter 2 vertical milling machine with fanuc 6M control.
Thanks
Hi
I have a problem with my kitamuraycenter 2 vmc spindle orientation. When it tries to do the tool change the spindle does not orient. It keeps running at slow speed. I tried m19 as well but it has...
Hi
In the program I write tool number and when it reads "T" command, it calls the macro automatically. e.g my prog will look like the following.
G54G90;
G28Z0;
G28X0Y0;
T3;
S500M3;
etc., etc,...
Hi Jim
Yes Please try the following macro program for tool change.
O9000;
G80M9;
G91G28Z0;
M06T#149;
G49;
M99;
Please inform me if it works for you.
Hi
Can anyone help me with the tool change macro program for our Kitamura Mycenter2 with Fanuc 6M control. We have lost the sub program for tool change after initalising the memory. We had a system...
Thanks everyone for their time and effort. I managed to clear "20 NMI Emergency stop' by moving away all the axises from LS by hand and press reset button on the panel.
Pcreek
Hi
I have the similar alarm in my Mazak Mazatrol M2. When I switch on the power the following alarm appears on the screen.
"NMI 20 Emergency Stop"
When I press "reset" button, the alarm disappears...
Hi
Thanks for the reply. When I tried to change the parameters I can see only the following pages.
1. Cut condition parameters
2. Point cutting parameters
3. Line/Face cutting parameters
4....
Hi
I can not send the program from pc to machine. But I can punch out the program from machine to pc. When i send the prog from pc to m/c it gives me an alram 470 Tape read error. I think some of...
Hi
We have just bought Nakamura Tome TMC20 CNC Lathe with FANUC 0-TC control. Can anyone help us in telling how to set the work offset and tool offsets in the machine.
Thanks
Pcreek