Search:

You won't find a manual that explains hopw to do the resetting after a ccollision, but here is the procedure that I use.
1. To check the alignment of the headstock, put a 1" pin in the collet...

You should have 220Volt, single phase in your shop. If you have it coming from the pole, You should have (2) legs with 110 Volt which when checked acrosss hould measure 220Volt.

Did you ever get the HNC retrofit going? I have one that I am starting soon.

I have a HNC Hardinge that I want to retrofit. How can I find out what the motor voltage is. They have only two wires going into them,
Thanks

Where are you located?

I found that if you are having a lot of tooling problems, call the Iscar, Valenite, Sandvik, Kennametal tooling person and almost always the person will pinpoint what the problem is. Also, he will...

Pull each board and slide it in and out of the connections a couple of times and check each wire terminal. Trucking can and will loosen screws and connections. Pull the connectors on the motors and...

Hi, I am in the Vero Beach area. I work on almost any machine. Let me know if I can give you some help.

I have had used and serviced KIA(Hyundai-KIA) for upwards of 20 years and in general they are excellent quality for the money. They are heavier than a lot of the other machines and hold sizes for...

check for 3 phase, be sure all legs are approximately equal.
check to see if spindle fan is ok
check fuses in control cabinet

Is the torque limiter actually popped out or is the proximity switch set so close that a little vibration is kicking it off?
Unless the torque limiter is bad, there shouldn't be a problem with...

g20 should change it to inch. Please be careful AS THE CONTROL WILL NOT CHANGE OFFSETS CORRECTLY

Is your cable made correctly?
You need to set the baud rate, etc. to the same in the machine and Mastercam.
Let me know exactly what you are having a problem with.

Contact Fanuc, the keypad membranes are $75.00-150.00 the last time I checked. You will need to identify what model you . Look in your Fanuc manual to see which you have.

By the where are you located. I am in Florida and do service for various machines. I was trained at Kia.

The pump has tripped an overload. It is likely that the pump or motor is gone. To check, disconnect the wires at the pump. (Note ) If wires are unmarked, be sure to tag them so it will run in the...

They are pretty much the same if used on a lathe. More importantly is how the control is married to the lathe. For instance, how the work offset is used, tool offset, tool presetter? The canned...

The main reason for a "Dead Length" Collet Chuck is to take pressure off the barfedder when you close the chuck as the collet does not m0ve backward. Also, if you use it as a chucker, the parts will...

Can't open the file, "not on trusted list"

I don't know if the Okuma uses different G-Codes but this is how I program a a bar pull when I have a X-Axis puller.

N100T1200(CALL TOOL)
GOG97M5(SHUT OFF SPINDLE)
X1.0Z1.0(APPROACH BAR)...

Look in the machinist handbook and program the minor dia..Run the part, measure with pitch diameter micrometer or thread wires and change your minor dia. so the next time you setup. it will cut...

Does anyone have any experience with adjusting a turret on an Ikegai FX15 with 6T Control?

The Yasnac controller uses only one line for threading. You can download a manual that explains the various G7-G78 canned cycles at:...

Your machine is probably not able to use the G80 series of Programs, I would think you have G70-G76 codes. The machine probably does not have rigid tap so assumming that, I usually use a pull-out or...

If those switches that you mention are on the hydraulic cylinder coolant collector, they do need to be adjusted to show open when the collet is open as control is waiting for confirmation that collet...

I changed out the solenoid coil on the index mechanism and now the turret does not line up, stopping about 30 degrees away. How do I adjust the turret? Thanks in advance for any help.

Have you checked your voltage. It should be 220 +/- 10%, ie. 208-242V with preference at the lower end. Also the legs should all be within 4-5 volts of each other.

I do servicing of these machines around Florida. Send me message if you are interested and I will give you a call.Thanks.
email: [email protected]

Thanks for the replies. I am making chips now and have a lot to learn about the control. However, I did get hold of the Anilam service dept. and they were very responsive. Mark and Jerry found the...

Go to "Edit", type "Oprogram name", Press "Input" After program name is in, then type what you want, then press "Insertt" for each word.