Update: We have been able to clear this error message. We did a careful X Axis alignment as well as turret rotation alignment. (Using a ground pin in a boring bar holder to sweep the VDI style...
Type: Posts; User: NPI
Update: We have been able to clear this error message. We did a careful X Axis alignment as well as turret rotation alignment. (Using a ground pin in a boring bar holder to sweep the VDI style...
We are trying to perform the Auto cycle for Turret Rotation Angle Setting. I have an Okuma Bulletin Number SBL0024. We are following the procedure as written. When we reach the line that tells us to...
I will do an alignment today. There is a tiny misalignment motion when the turret clamps.
The proxy switches have not been touched. I have not been able to get the alarm by manually indexing the turret. One station at a time or holding the button and randomly stopping at different tool...
Story:
Original owners.The machine has been running fine. A fair amount of live tool work for the last week.
No collision.
Running a schedule of 18 parts. It will randomly throw the alarm.
The...
We are seeing the error 1783. I have read quite a few threads regarding this. Stumped. I switched out the solenoid to see if that was failing. Same result. I have the turret cover removed. It's clean...
Our VTXU alarm when the tool carousel doesn't stop and line up correctly. The tool pockets travel just past where they should. They sometimes back up a little and it's fine. We changed the motor as...
Hi,
I have a Cosen G320 automatic band saw. (we bought it new a few years ago) A week or so ago it started to not feed the programmed amount of material for the next cut. You can watch the rear...
I have an older EZ Path. I remember that error but not how to clear it. I think it has to do with you UCS (User coordinate System.) having been shifted when you hit the F1 or W Shift key. That W...
We have found that this alarm can not be cleared until changing the 3.6v lithium battery located on the turret drive in the main cabinet out back. We do this battery change while the machine is...
Hello,
Drisson LLC can help you with software. I changed out some hardware and bought software from them.
https://bptparts.com/collections/ez-path-romi
[email protected]
Good Luck,
Jon
Homing problem cured. There were two wires crossed going into JP 10 on the AUXBOB card. We had replaced the cable and had incorrectly installed these two wires.
This not homing issue has been narrowed down. We are not totally done yet but it has something to do with the cables and or hold button up in the pendant. When we unplug JP10 on AUXBOB board the...
We have an EZ Path I that we purchased new.....
We have changed the X cables for everything. We also updated to a new back plane and motherboard with a COB, new software was pre-installed.
The...
Hello and thanks for writing. The level sensor is electric and mounted on the left side of the upper head. It has three sets of probes that detect the water level. They may be sending a reading to a...
Hello,
We have an AQ327L WEDM. The issue is that the water level ends up totally filling the tank when burning under high flushing pressure. The level sensor is working (or is trying to work) if...
We have not found a cure yet. I was hoping that maybe you had.....
Jon
Okay. Some issues were found. (loose wire conections etc.)
Now when we go to "home" the machine, the "Z" axis doesn't jump, the Alarm "Drives not on, cannot home f4 flashes up then "Axis Driver...
The Z does not jump with the JP9 plug pulled from the AXSBOB card. The "drives not on, cannot be homed" alarm still comes up.
We did find a pin not making contact on the X manual jog hand wheel...
The actual message that flashes by is "drives not on, cannot be homed"
We are looking for loops that may not be closed in the system.
We are bringing a 95 EZPath back to life. The screen alarms an axis drive fault. If we hit any key, the Z axis (momentarily) moves towards the chuck. We have something crossed up and it is not...
We have a B & S Reflex 343 here that we purchase new in 97.
The LCD screen has been failing. Does anyone know if we can find these screens or change it out? B&S only offers a $4500 change out to a...
Hi,
We have the CR1 error again on our TC2. There is an red LED alarm light on the "Y" axis drive. (same as before)
We had changed the "Y" drive when the happened last time and the fault went...
We have completed the swap of the x and y drives. The alarm stayed on the original Y drive.
What are some recomended sources to obtain a replacement. As I understand it the drives have parameters...
The machine is a TC2, not a TC 22.
We will try the drive swap out.
More info is now available on the CR1 not enabled alarm.
The Y axis had bound up due to chips building up around the lead screw area. This has been cleaned up and you can now (with considerable...
We must have a different panel lay out because there is only the gold control box in the top left area of the cabinet.
We'll look into it further.
Thanks for the relpy!
Jon
Hello,
We have an TC-22 here that is displaying a new error. (to us anyway)
"CR1 Not Enabled" We see that CR1 is a Relay. Do any of you folks know how we can trace this out or resolve this...