Thank you mbservice, sinha_nsit and generaldissara very much for all of the help with my Storm 80. After working through the G-Codes, everything is working very well now. I just turned some parts,...
Type: Posts; User: Bill Gillen
Thank you mbservice, sinha_nsit and generaldissara very much for all of the help with my Storm 80. After working through the G-Codes, everything is working very well now. I just turned some parts,...
Thank you for your reply. The G94 fixed it!
My 3401 parameter is currently 01000001. I have not changed it yet, and am thrilled to get the Storm running. What does it affect?
In...
Thank you for the info. The G97... program was nearly dead on, at 999 rpm. Then tried in MDI the G99 G97...... It also worked, exactly one inch per minute.
Bill
Hi all,
I finally got my Cyclone Storm lathe with Fanuc 21i-T controller operational. What is baffling to me is the feed rate on the machine doesn't match what my program is telling it. For...
Hi,
I have a 10T keypad/circuit board giving me problems on my Wasino Turning Center. I have a good 10M keypad/circuit board.
My existing 10T keypad/circuit board has N860-3487-T010 on it....
Hi all,
I wanted to ask if anyone could recommend a good Service Tech for a Clausing Storm 80 CNC lathe with Fanuc 21i controller that will cover North Georgia (Gainesville).
I have been...
Hi all,
I wanted to ask if anyone could recommend a good Service Tech for a Clausing Storm 80 CNC lathe with Fanuc 21i controller that will cover North Georgia (Gainesville).
I have been...
Thank you!
Although it turned out not to be the soft key pad or the keypad the ribbon cable plugged in to, you helped me get on the right track. While in there on Sunday, I also went into the...
Hi all,
I have made some progress with a Storm80 with Fanuc 21i controls that I bought, but it is still "stuck" in E-Stop mode for some reason. I was finally able to set the parameters to the...
I was able to successfully download programs, upload parameters and get the machine to run numerous cycles (with no tools). As I was getting more familiar with the controls, it seems that the right...
Hi ,
I downloaded the parameters from my Wasino with 10-T controls (in case I goof something up). I saw a lot of symbols flashing across the screen, and wondered if that is what I was supposed to...
Hi,
Thank you again for your help. I walked through your instructions on my machine, but still am not sure what I am looking for. The pictures I posted on this reply show the A0000.1 code message...
Thanks for all your help up to this point. However I now have a new issue. I have learned how to navigate through to the ladder. I learned to hold the shift key down to bring the A up. So now i have...
Thanks for the replys
I have a pdf copy of the ladder not sure what to look for`
do not have a copy of the parameters but the look to be thre
I put up photos of the parameters and the ladder
It...
Hi all,
I have made some progress, but it is still "stuck" in E-Stop mode for some reason. I was finally able to set the parameters shown in post #3 to the correct 00110000 (a friend came by and...
This may help
189566
I have installed new batteries thats when i got the alarm 1001 and the -eng-alm.189522
Thank you for the reply. I'm still beating my head against the wall with this.
To start off with, the machine came with no batteries in it (first picture). After I installed the batteries, I...
Alarm message 1001 spindle speed monitor - no respons
What is the best procedure to try to correct this
Thanks
Bill
Hi all,
I just had the good fortune to win an auction for a Clausing Storm 80 Lathe Serial # T70129 with a Fanuc 21i-T CNC Control. Now for the bad news. Someone took the batteries out of the two...
I just want to say thank you to both erniel and bbaloghe for their help. Your suggestions got me close enough to make it work. For some reason, my Denford lathe rejects the T0606 on line N170. ...
Hi all,
I am having trouble trying to taper bore a part, and believe I am not understanding the tool offset. My control does not recognize G50 offset. I tried using:
N130 M06 T0625 . ...
Hi,
I bought a Wasino LJ-63M CNC Lathe a few months ago, and finally got the mechanicals running. Now I want to learn how to use it. It came with an LJ-Series Operator's Manual. However, when I...
Hi all,
First, I appreciate everyone's help with getting my Torq Cut 22 going. It is really running great. I love having the 7500rpm spindle, and the machine operates much quieter than my...
Hi,
Think I can help a little. PM me with your email address and I will be glad to send you the parameters I am using on my 1988 Denford Cyclone with Fanuc OT-B controls when I return on Monday....
Hi George and all,
First, thank you for all the replies. I am now able to dry run programs, either through MDI, or from modified versions of my posts from ONECNC.
I looked up in the spindle,...
Hi,
Made some more progress. I looked at the recommendations, and one thing I noticed was I never saw RPM being displayed. I gathered from all this that my encoder might not be working...
Hi,
Thank you on the offer. I have it running now, and do not think that is the problem any more. If you could, may I ask you to look and see if it is wired the same as the schematic I posted...
Hi George,
It's pretty cool that you worked with this one over 16 years ago.
We looked at the current wiring and then the schematic some more, and then thought "Damn the torpedoes! Full Speed...
Hi George,
Thank you again. After reading your post, I went into the spindle motor cover, and looked at the 12 pin connector. I immediately noticed that one of the white thermistor wires from...