Thats what I got when they started that backorder stuff, I waited a little bit and one day said ok I am getting the PM45 .... love it glad I got it instead
Type: Posts; User: The_Tuner
Thats what I got when they started that backorder stuff, I waited a little bit and one day said ok I am getting the PM45 .... love it glad I got it instead
An update on this since I got no replies perhaps this could help someone else.
I ended up just mixing it 8 ounces per gallon of tap water instead of the recomended 4 ounces per gallon, I had read...
I have read numerous posts of this stuff causing rust, read as many said they get no rust of their machine's as well ... I live near Pittsburgh PA ... we have city water and its deemed as hard water...
Well when we got our PM45's they had pretty much just came in, love mine as well, in fact for me it actually couldn't be any better for what I do, does everything I need it to do and then some, its a...
I agree Pete ... a small bushing with a lip would be great for these, the uncentered spinning drawbar is getting on my nerves ... my drawbar is also a little over 19 inches as well, however using the...
I don't think taking that off would do anything since its meant to be loosened for the tilt anyway, taking the colum off would be more what I was thinking.
Reverse, yes more noise, nothing more...
No insult taken at all .. thats your opinion ... Matt at Precision Matthews flat out told me where to put it and thats where the balance point is, I did not guess where the balance point was (when I...
I used a load leveler, though I acheived what was perfect balance without removing the head, or as close as you can get for such an item ... I used an automotive 2 inch wide ratchet strap near the...
Lol no ... I will call him and get that info ... I sort of left it as is since I wasnt going to use that portion right away, but yeah I need to get that hooked up so I don't have to worry about it...
Yes, hots make no difference either side will do
They are 220 I have exact machine, got it last week
Green is the neutral, center position ... then two power wires on left and right
I opened the power control switch box on the machine to make sure that was the neutral, just a few screws you may...
Floor to top of table 34 7/8"
PG is used in alot of stuff ... fog machines ... its the base liquid in electronic cigarettes (makes the smoke,fog), nebulizers.
Below copied from Electronic cigarette - Wikipedia, the free...
Let you know tomorrow on that height.
I ran a 20 amp 220 volt line, thats plenty, you will need a receptacle and a plug because these just come with bare wires, no plug included.
Coolant pump,...
Thats what I used, got them at Lowes, they are stronger than lug type I am told
There isn't a plug on them, you have to purchase that, I just got done wiring mine, everything is wired except I have to get a circuit breaker.
Lift point is just under square part of head, there...
16" wide x 28" deep for the bottom of the base
Chipslinger its 81 inches all the way up as pictured
Yes its pretty much same as G0704 in that respect ... half inch slots and R8
Guess a bigger vise would fit on the table 6 inch would be at home
Thats a good thing ... you now have the option to use bigger tooling as well as small
Nice, wish I had the funds to have got the DRO, that is really handy ... oh well one day I will get it ... im jealous now lol
Chipslinger, Matt at PM when I was there friday had a PM25 for sale (only one he has), though it had 2 axis DRO on it and he wants to sell it that way.
I will go down and measure that for you in a...
All bolted down and leveled, finally ... takes more time than I would have thought, there was a very long bolt under the paper on the table, gotta figure out what that is for lol ... oh yeah the...
Lol thanks ... yeah they were remodeling a store and throwing those away, not a thing wrong with it either ... oh yeah it is a 42" plasma ... looks tiny on that wall I know.
My thoughts are if you...
Thanks for the replies, see I looked for this over the internet and as you can see above this is what I found, people really have differing opinions on this ... its hard for me to find a fine thread...
Again Hoss thanks for the info, I watched the RF45 video's as well when I looked at the G0704 stuff, the best was the install into your house for me because I don't think people realize they can...
Well no ... its what you would think in an industrial park ... bay door for a tractor trailor to backup and a very long warehouse, tons of stuff in there, I saw like what looked like a 20 foot or so...
Cancelled my order for the G0704 yesterday, just too much fear in the actual delivery dates, beside I need one for a project ... went to Precision Matthews and got a PM-45M with Power Downfeed, came...
Ok I am going to hand tap some 1/4" diameter holes into 6061 aluminum they will also be about 1/4" to at most 5/16" deep .. I will be using 1/4" steel set screws in them to hold some plastic parts. ...