Hi Amf11,
Could you find a solution?
We have the same problem here, but in our case D-params are 0660-0669
I would highly appreciate any hint that could help to solve EX-1047 problem.
Type: Posts; User: igorko
Hi Amf11,
Could you find a solution?
We have the same problem here, but in our case D-params are 0660-0669
I would highly appreciate any hint that could help to solve EX-1047 problem.
Hi Everyone,
I need help too.
Can you kindly share how to solve EX-1047 alarm?
I have input all parameters, except DIAGNOSTICS 0660-0669
It is impossible to input them.
Any help would be...
Dear Friends,
Thank your very much for being helpful!
I am sorry for the delay - we checked the Input power unit (where the wires from buttons On and Off lead to)
It seems alright.
I tried...
Hi Braided,
Thank you very much for the hints.
I tried them now - unfortunately it wasn't our case - nothing changed.
We are trying to check everything what we can, but with no documentation...
Thanks Ifixcnc.
Do you know how does master PCB start?
Is there any 'enable' signal/wire?
Dear CNC Guys,
Our FANUC OM (model B) stopped working: the screen is blank and there is no diagnostic whatsoever.
(When switching off - the CRT flashes a little, so we can see that it was a kind...
Thanks for looking into my case Tc429!
No, I am in Auto mode. And the program is registered in memory.
But you're right, it seems very similar to that.
Is starting of a CNC program anywhere...
Hi Everyone,
We have got a very strange situation with FANUC O-L control (AMADA LCE-645 laser cutter)
We switch on the machine and everything starts Ok till the moment when a CNC program should...
We are using small devices Moxa Embedded Device Servers NE-4110S - Embedded RS-232 Serial Device Server (10/100 Mbps, 115.2 Kbps max.)
to connect our CNCs to network.
If you've any qustion, you...
Dear Friends,
Can you help me with parameters manual for Fanuc O-L series, please?
[email protected]
Any help would be highly appreciated.
With best regards, Igor
Did anyone get the OL manual?
I need it much too.
[email protected]
With best regards, Igor
Dear Friends,
Does any of you have a parameters manual for FANUC O-L series control?
We got an old laser cutting machine AMADA LCE-645 and there is unfortunately too little information about the...
Hi!
I can send our parameters, but one should be careful with them, because they might differ quite much from machine to machine.
I would recommend to contact INDEX service with your machine...
Hi!
If I got it clear, I had a similar problem recently - when I commanded
G0 G28 G91 Z0 the machine moved down to the absolute coordinate and then up to the reference point (this is normal...
Hello Marco,
We had a problem with E-stop when installed our Matsuura MC-760 MX3 machine.
There is an electrical circuit connecting all parts of the machine that can break the circuit if there is...
Hi!
We have just installed Matsuura MC-500V2 Yasnac MX2 machine.
We are using HSMWorks (HSMWorks • Integrated CAM for SolidWorks) for producing programs. It has generic YASNAC post, but if you...
Did you manage to get all memory working?
Here is some good information that might be of help:
Memex Automation
(try Save link as...)
I wander because we have the same task.
Hello Guys!
Is there anyone using INDEX GB65 (GB42, GB100) CNC lathe(s) here?
Or anyone familiar with these?
Would be grateful for reply.
Thanks in advance!
Thanks very much Atom!
Good lesson for me.
Dear Sirs,
Thanks a million for the responds.
I'm delighted with all of you.
And once more thank you very much for you time.
P.S. Yes, G41, G42 is one of the most complicated...
Dear All,
My newbie question is about G41, G42
Is it possible to mill a hole 8.4 mm in diameter with 6.5 mm endmill using G41 (G42)?
The hole is 20 mm deep.
If so, could you, please give the...