Search:

They work for me, just open them in a text editor like wordpad. I suspect there's a way to import them directly as well.

Sounds like your VFD, search vector drive on this site for a ton of info.

I'm curious about this too, I had hoped for some responses today. We change cabinet air filters regularly, ensure fluids are topped off at the start of each shift. We need some sort of sump...

Do you have the macro option installed on the machine? If not, there is most likely a 200 hour trial period.

no need for the [ ]

Is this for a haas control?? If so, get rid of all the v's and r's...just use #. Also get rid of all the +'s.

It IS in the blue book in the electrical cabinet! Thanks!

Where can I acquire a list of keep relays for my machine? PUMA 2600SY manufactured 2012-09?

looks good!

Thanks Darryl, I got the drive lug oriented correctly. The pulley had slipped on the taper, so I loosened the bolts aligned the drive lug, oriented the pulley and tightened everything down. The...

Thanks Darryl, email sent.

Thanks Dhardt, very helpful and informative as usual. The turret IS in fact in overload state. I pulled the live tool holder in the cutting position out, and the drive lug is not aligned. I have a...

I was running a part that has been running all day. After finishing a live tool cut on the sub spindle, the turret retracted to it's tool change position, and then alarmed out with "2149 servo drive...

On the back (or side depending on model) of the machine there is an oil coolant separator, usually with a plastic bottle to catch oil. Remove the screws and clear it of all the snot that builds up...

Sounds like you found your problem. Replace your Z home switch.

paste it here please

I went to find this in my control...turned setting 23 off, and it wasn't there. But, I ran a G47 program and in single block I can clearly see that the O09876 program is running. If I could figure...

Use macro O9818 " 4th Axis Y Measurement ". I use O9817 x measurement all the time for truing surfaces to the spindle on my horizontal mill. I you need the specific pages from the manual, I can...

I got it figured out. parameter write needed to be on for the timer button to show up.

How do I change the value of a timer on my 2600sy fanuc 31i-a control? It is set to 20 seconds by default and it takes longer then that to load a bar.

5 year old post guys

At our shop we use PC-DNC Plus, I have used hyper-terminal on occasion, Predator is good software, I really like their editor. Just make sure all the parameters (port, baud, stop bit, xmodem) match...

Use rs232, ensure all you settings match in the pc and the VF. Set dnc from mdi in the settings page then hit mdi twice to receive the nc.

G97 Cancels constant surface speed control and sets the lathe spinning at 3600 rpm. This is like a safety line...it's good to cancel all modal values at the start of a toolpath. Also, you get a...

2nd for Lucy's Machine, great people to deal with, fine products.

This should be a good place to start, use with caution as I don't know your setup.

https://docs.google.com/file/d/0B3vNRy_73pkfLXNuWUtEX1pzZkk/edit?usp=sharing

Bill,

Thanks for the info. I had come to the conclusion that this was a shotgun approach as well. We had the 40hp drive for our ec400 repaired as we could not afford the downtime to...

how about something along the lines of:

new bar loaded -> set a variable to 100

:begin

make a part

part cut -> subtract length variable plus cutoff from the same variable you set to 100...

here you go: https://docs.google.com/open?id=0B3vNRy_73pkfV2NYNmJvVVU2Qlk

We have all the machines listed in our shop. The EC-400 is pretty sweet if you regularly run thousands of parts, but the setup time makes it a poor choice for prototype work. The vf-1 is a good...