Search:

Hi, I have a 4'x4'x6" table with a 3.25 horse Porter Cable that is looking for additional revenue streams. Just looking to do some basic 2 ply plastic custom signs, the kind with a colored top layer...

Hi All,

Haven't been around in a while due to some Microsoft certification studying, but here it goes. I have a Dyna CNC router and everything seemed accurate until I recently tried to do some...

Does anyone who has this particular setup tell me what color the wires on the table I/O interface are. I'm trying to narrow down my problem. For the record I have, left to right

(X) dark blue,...

Alright, duh, now I get it, so when I do a dial indicator test, i should just go by the DRO and compare the results, or do the math to see if the machine is on or off. Then I can get back to my...

So, why would it be off at .010" as well?

Thanks for the reply ger21, should I change the step to 2000 and try it from there, or are there limitations of some sort that I should be aware of?

My X and Y are at 1878.27
Z is at 20000

These are the settings of the set file from DynaCNC

You may know me from the Rhino forum where I've struggled to get good circle from my DynaCNC 48 x 48 table running Mach3. I've eliminated Rhino being the source of my problem (thought it was an...

Well, got the dial indicator out, maybe I should be posting this in Mach since it's definitely not an export problem with Rhino. The table is off on both axis. When jogging in steps at .001, the dial...

Had a busy weekend, away from my machine unfortunately......

Thanks for the file, InspirationTool (Jeff) and all of your help. The cenetered circle file did not result in any differences. I have...

I've disassembled X, everything is tight and the belt is good. There is nothing mechanically wrong with X. The machine has very low hours because it's been down for most of it's life. Here's the code...

Thanks for the advice, I'll go through X again, however, I am not the lone ranger around here when it comes to hacking DynaCNC. This has been the least of my problems with their customer service and...

Here's an image, the same defect happens in every circle in the same spot, regardless of size.

Great interview, and a big thanks to Novedge for providing me with Rhino at the best possible price.

Well, tried everything suggested, all the belts and gears seem fine, tried cv off with various levels of backlash but still have a noticable imperfection on the circle on the same spot everytime....

now that I'm back up and running and back at square one, I've been just trying to get a perfect circle on my machine. Background.....I'm going from Rhino 3.0 to Sheetcam 4.0 into Mach 3 machineware...

Haven't been around much lately, once I got my machine up, the computer that runs it took a mobo crap....arrrgh! I had to step away for a while and collect my wits.....Beautiful stuff, I too , would...

I have a Pentium 2.8 , 1GB RAM , the computer is not connected to the net and has very few programs on it (sheetcam, mach, acrobat reader,and rhino) I'm running Mach v. 1.83.005, it's a router. The...

The X and Y run beautifully, they all have the same resistors. It was a commercially built table, so I assume they know what they're doing.

Her ger21, thanks, I also tried that, still has the same behavior. I'm definitely a newbie, but I seem to be a lot more concerned than DynaCNC (Dynamic Plastics) about the fact that after 6 months of...

Thanks Art, I tried but still have the problem....any other suggestions?

I have a DynaCNC router with steppers, running Mach 3 and have an intermittent problem, not sure if it's the Gecko or not. My Z axis locks up whenever I run a file, I can jog it all day long without...

You probably had a machine that worked great right out of the crate. I did not have a working machine out of the crate and they basically treated me like I was the problem. When it finally came time...

Hi turmite, thanks for the reply.

I did try the specified file, and it appears to be right on, however, like the others that I have done, the same problems keep creeping up. It looks great on...

Hey all, I'm trying to do a "correct" Fender Telecaster body by using a hi res bitmap to trace the outline. It seems that no matter how good the outline looks on the screen, there are various dips...

I can't say I'm all that happy about the way I was treated as a DynaCNC customer, I paid a couple hundred dollars in shipping for exchanging parts that were DOA on my machine. Tech support was...

I think it will be if it does what they say it will, however, I've scoured the net and haven't found one review of it.....

Holy smokes!!

I'm a relative newbie to CNC and just started working in Sheetcam, having formally relied on Mach 3 for G code ....so far, it seems like Sheetcam is more intuitive. When I export a file in dxf with...

Novedge seems to have the lowest price, and they're listed on the McNeel website as an authorized reseller. $599, their bundles are great deals as well.

http://www.novedge.com/Rhinoceros_Rhino.asp