Search:

Check your auto probe pattern parameters, make sure that the parameters are setup for this type of fixture and that the auto comp/calc parameters are correct. These parameters are in your parameter...

Check your barrier grid shift position after so many parts performed. Barrier grid and pattern are in your parameter manual.

Htech.

Sounds like you’re going to have to do a type of hard boot, manually booting the system. The reason you cannot do a system disk boot is for the fact that you have lost all parameters, there is a...

Send me all the information of your control, you can access this information from the maintenance screen. I will send you the the wiring info or any other info you need.
Htech,
X Mitsubishi...

Tell me the connections and i will give you the connection locations.

I have a Fanuc 10M control, how do I setup this control to drip feed from my PC.

Help please

Hi everyone!

Can anyone help me, I have a J&L 4521 retrofitted with a Siemens 802C control, I need to view the ladder, how do I access the PLC Ladder.


Thanks,
Htech.

I know the MS NT5400 series that has a 32 series F control and also a Mazak HS series with the E series control.

Give me your email and I will send you the procedure.
Htech.

Hi,

Can anybody help me out; I have a Kuraki HBM 10-DX with an 11M series control. There is not enough memory to do most of the jobs, so I end up loading only half of the program to start then...

Go to the Interstate battery web site, they have the same batteries for $11.00 as to the $86.00 you will spend at the OEM, BUT I HAVE TO WARN YOU, if you are putting these batteries in a component...

Hi Dave,
I can help you over the phone, I live in Texas and I am ex-Mitsubishi.

email me if you need help.
Thanks.
Htech.

contact MEAU, if the machine tool maker cannot help you then you must explain this to MEAU, they have a library and they should be able to help you out.

do you have a load meter, if so use the pulse generator and watch the load, at a smooth movement it should be steady, if the meter fluctuates, then check the amperage at the motor, if that is ok then...

I do not know how bad of shape your HD is in, but if you have a machine of similar type, there is a software called Drive Wire Clone. This software enables you to clone a HD, this is an option.

i do not know if it is too late for you recover the old drive, but there is a software called Drive Wire Clone. this software enables you to clone a hard drive, if you have a machine of the same...

tell me what the load meter looks like, i might be able to help.

I have recently launched my own CNC repair company; I troubleshoot and repair all series Mitsubishi CNC controls that includes all electrical devises that are controlled by the CNC. I love to...

All of you guys are correct; a Mitsubishi control is shipped fully loaded and for an additional sum you too can have more options. What are required are the pass codes and the options parameter...

if mazak cannot help you out, you can then go to MEAU, they have an archive and this should get you going.

you will have to contact the OEM first to get the parameters, if they are of no help, contact MEAU, they have an archive and should be able to help you out.

I worked for MEAU as a field service engineer for ten years; I covered the southern and Midwest regions.

if you have the original electrical drawings, the information will be there.

disconnect U V & W at the AMP. power the machine up. if alarm is still there, you have a bad Amp, if the alarm goes away,you most likly hve a bad encoder. you really need to put a MEGER on the motor...

Hi!
Can anyone help me with a Fanuc T6, this T6 does not have a geometry page, so the operator is using G50 for offset and tool comp. I was asked the question? How do you teach the tool with this...

Hi!

Can anyone help me with the procedure to accessing the ladder logic of a Fanuc OTA/OTC series control, can this be displayed or do I look at the bit information.

Thank you.

You can get a great deal of info for free from the MEAU tech support, but then again what you are probably looking for is in the MEAU red books, I know, I was employed with MEAU. If you cannot find...

I have an INTERGREX E500HS, I was told to generate a list of spare parts so that I can order and then build a spare parts area for this particular machine. Can you guys with what you have experienced...

INTERGREX E500HS/640M PRO:

I am having a problem with the Z-axis, I cannot hold a depth of + or – 4thousands, when I insert my Z-axis offset to compensate, the Z-axis will float again. MAZAK has...