ph-cleantec
Products
Clearly Clean Results
33
ph-cleantec GmbH
Cleaning machines
1000 SRE Low pressure hot cleaner
1000 SRE
| Machine characteristics |
|
| 65 kg | |
Application:
Parts cleaning and machine cleaning, especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools incl. cabin, magazine, spindle and gear room, also for retrofitting, small and large components. Also ideal for cleaning large parts in combination with large collector 1000 SRS.
The working principle is based on the high temperature combined with low pressure: at 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the soiling without damaging parts. Thanks to various nozzles, even complex surfaces, including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Cost- and time-intensive installation and removal of individual parts can be avoided
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: Thanks to the 60-litre tank, independent of permanent supply of cleaning medium
- Suction of own cooling lubricant possible; allows cleaning with own emulsion without introduction of foreign substances
- Higher work safety and significantly lower costs than manual cleaning with rags
- Kind to health
- Complete elimination of chemicals, thus reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environmentally friendly
Technical details:
Mobile. Without dirt water collector for parts cleaning.
5m hose with lance pistol and changeable 600mm spray lance; hose attached to chassis via quick change coupling. Start-stop operation with pistol. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 7.5 bar and 1.8l/min. 10.1 KW, 16 Amp.
Parts cleaning and machine cleaning, especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools incl. cabin, magazine, spindle and gear room, also for retrofitting, small and large components. Also ideal for cleaning large parts in combination with large collector 1000 SRS.
The working principle is based on the high temperature combined with low pressure: at 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the soiling without damaging parts. Thanks to various nozzles, even complex surfaces, including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Cost- and time-intensive installation and removal of individual parts can be avoided
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: Thanks to the 60-litre tank, independent of permanent supply of cleaning medium
- Suction of own cooling lubricant possible; allows cleaning with own emulsion without introduction of foreign substances
- Higher work safety and significantly lower costs than manual cleaning with rags
- Kind to health
- Complete elimination of chemicals, thus reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environmentally friendly
Technical details:
Mobile. Without dirt water collector for parts cleaning.
5m hose with lance pistol and changeable 600mm spray lance; hose attached to chassis via quick change coupling. Start-stop operation with pistol. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 7.5 bar and 1.8l/min. 10.1 KW, 16 Amp.
1000 SR Low pressure hot cleaner 95°C 7 bar
|
Cleaning machine
ph-cleantec GmbH
Cleaning machines
1000 SR
| Machine characteristics |
|
| 100 kg | |
Application:
Parts cleaning and machine cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools, retrofitting, small and large components.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles even complex surfaces including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Units in the SR family have an attached collector with a special recycling and sedimentation system. Smaller parts up to 80 kg - filters, ball bearings, motor parts, gear parts etc. - can be cleaned in this collector. The used cleaning medium is cleaned and recycled.
When cleaning machine tools, cooling lubricant from the tank of the machine tool is sucked in and heated. The machine tool - cabin, magazine, spindle, electric parts - is sprayed with the hot coolant using a lance.
Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Less machine or part breakage
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: thanks to the 60-litre tank, independent of a permanent supply of cleaning medium
- Higher work safety and lower costs than comparable systems such as cold wash table, bio-wash table, A1 sprays
- Health-friendly
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly
Technical Data:
Mobile. With dirt water collector for parts cleaning with robust drip grid (90 x 60 cm). Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, and 2m hose with spray pistol and changeable standard nozzle; both hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 7.5 bar and 1.8l/min. 10.1 KW, 16 Amp.
Parts cleaning and machine cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools, retrofitting, small and large components.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles even complex surfaces including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Units in the SR family have an attached collector with a special recycling and sedimentation system. Smaller parts up to 80 kg - filters, ball bearings, motor parts, gear parts etc. - can be cleaned in this collector. The used cleaning medium is cleaned and recycled.
When cleaning machine tools, cooling lubricant from the tank of the machine tool is sucked in and heated. The machine tool - cabin, magazine, spindle, electric parts - is sprayed with the hot coolant using a lance.
Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Less machine or part breakage
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: thanks to the 60-litre tank, independent of a permanent supply of cleaning medium
- Higher work safety and lower costs than comparable systems such as cold wash table, bio-wash table, A1 sprays
- Health-friendly
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly
Technical Data:
Mobile. With dirt water collector for parts cleaning with robust drip grid (90 x 60 cm). Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, and 2m hose with spray pistol and changeable standard nozzle; both hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 7.5 bar and 1.8l/min. 10.1 KW, 16 Amp.
1500 SR Low pressure hot cleaner 95°C 14 bar
|
Cleaning machine
ph-cleantec GmbH
Cleaning machines
1500 SR
| Machine characteristics |
|
| 120 kg | |
Application:
Parts cleaning and machine cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools, retrofitting, small and large components.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles even complex surfaces including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Units in the SR family have an attached collector with a special recycling and sedimentation system. Smaller parts up to 80 kg - filters, ball bearings, motor parts, gear parts etc. - can be cleaned in this collector. The used cleaning medium can be cleaned and recycled.
When cleaning machine tools, cooling lubricant from the tank of the machine tool is sucked in and heated. The machine tool - cabin, magazine, spindle, electric parts - is sprayed with the hot coolant using a lance.
Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Less machine or part breakage
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: thanks to the 60-litre tank, independent of a permanent supply of cleaning medium
- Higher work safety and lower costs than comparable systems such as cold wash table, bio-wash table, A1 sprays
- Health-friendly
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly
Technical Data:
Mobile. With three heating elements. With dirt water collector for parts cleaning with robust drip grid (90 x 60 cm). Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, 2m hose with spray pistol and changeable standard nozzle; both hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 14 bar and 2.8l/min. 15 KW, 32 Amp.
Parts cleaning and machine cleaning especially for greasy, oily and complex surfaces. Ideal for cleaning machine tools, retrofitting, small and large components.
The active principle is based on high temperature combined with low pressure: At 95°C, greasy and oily contamination is dissolved quickly and efficiently. The low pressure is sufficient to remove the contamination without damaging parts. Thanks to various nozzles even complex surfaces including deep blind holes and cavities, can be cleaned easily and without leaving any residues.
Units in the SR family have an attached collector with a special recycling and sedimentation system. Smaller parts up to 80 kg - filters, ball bearings, motor parts, gear parts etc. - can be cleaned in this collector. The used cleaning medium can be cleaned and recycled.
When cleaning machine tools, cooling lubricant from the tank of the machine tool is sucked in and heated. The machine tool - cabin, magazine, spindle, electric parts - is sprayed with the hot coolant using a lance.
Advantages:
- Significant time savings of usually 80-90%.
- Reduction of expensive machine downtimes
- Less machine or part breakage
- Mobile, i.e. can be transported from place to place without any problems
- Self-sufficient: thanks to the 60-litre tank, independent of a permanent supply of cleaning medium
- Higher work safety and lower costs than comparable systems such as cold wash table, bio-wash table, A1 sprays
- Health-friendly
- Generally no need for chemicals, hence significantly reduced procurement and disposal costs
- Less water and waste water
- Thus resource and environment friendly
Technical Data:
Mobile. With three heating elements. With dirt water collector for parts cleaning with robust drip grid (90 x 60 cm). Water recycling via special sedimentation system and filtration with active filter monitoring.
5m hose with lance pistol and changeable 600mm spray lance, 2m hose with spray pistol and changeable standard nozzle; both hoses attached to chassis via quick change couplings. Start-stop operation with pistols. Stepless pressure adjustment.
Water supply without pre-pressure from 60l tank, 5l container and dosage unit for cleaning agent, overfill control, water shortage disconnect, overheat fuse.
Capacity ca. 14 bar and 2.8l/min. 15 KW, 32 Amp.
