Anyone have a good coolant pump they're looking to get rid of that matches a VBV-44M Gusher pump??? Thanks Tony
Digital. Experienced. Powerful. - 100% Tool Management
Type: Posts; User: mbm
Anyone have a good coolant pump they're looking to get rid of that matches a VBV-44M Gusher pump??? Thanks Tony
Hey guys I am having a issue with our chuck, Its a Kitagwa B10 and if I externally clamp on round stock I have no issues at all (clamps part good)... If I internally clamp on something the jaws open...
Thanks for the reply, it is a issue with the switch... Got a new one coming
Hey guys we have a Cadet 4020 with a 5020M controller, our A drive wont turn manually and when we program a movement we get a 117 A Alarm. Its a "20" code on the alarm which states: "Rotary Table...
Its a 1991 machine, we found the board - removed it, cleaned it, and reinstalled.... So far so good! Found one on Ebay reasonably priced that had been re-worked with a warranty too for back up!...
Hey guys we have been having this alarm pop up intermentatly and now its coming up everytime we start the machine now.The machine is a Cadet 4020 with a 5020M controller and the alarm comes up as:...
I am having some issues with our tool changer and would appreciate any input on what may be going on... When we try to make a tool change commamd heres is whats happening: The spindle lifts to the...
Hey guys we just had this alarm come up on the monitor, it has a OSP 5020 controller. Any ideas on what may be goin on. The manual says to reset the lube pump motor. However cant seem to find a reset...
Awesome thanks for yalls help
Hey guys I have to tap some some metric threads threads in a shaft on my Okuma LB-15 lathe. Im going to be using a 6mmx1 pitch tap, in a floating tap head.If I run my machine in standard, a feed rate...
Thanks got it to the change however the time gains were minimal, so crankin up those speeds and feeds a lil more...
Hey guys is it possible to make a tool change with turret next to the chuck in X, as of now I have too run the turret as far up in Xas it goes. I am running 4000 parts and could save time and wear...
OK a little confused now, I think I found the drive unit now here's where i'm not sure. There is writing on it that says BLIID, now the wires are tagged "BDU MG".There are LED's on the left side of...
Help guys this morning we came in and started to our get machine set up to run some parts,while doing some programming this alarm popped up. So we got the alarm book out and looked up alarm # hit...
Ok changing the K to I did it, and have my guide working correctly. Cant thank you guys enough, Life is good today!!!!
Still fighting and kicking but heres a lil more info that may be helpful, I typed in T000404 and i went to the correct depth but X was a bit small. If I go back to T040404 I end up deep again but...
Well thats a good ? On every tool but the boring it gives me a interference point in the guide block, the guide block for the boring bar says "no entry" . Still very new to programing and just...
Hey guys im having an issue with my Z depth going in deeper on the last cut of a roughing cycle. For instance yesterday I was running a part and I drilled it to make room for my boring bar. MY boring...
Hey guys been having an issue with a communication board. Went bad over the summer,had it repaired and now its crapped out again. Going to send it back under warranty claim however was wondering can...
No were still down, been all over this thing. We can run it just no ATC, going to have to have a tech come in I guess.....
Hey guys been fighting our tool changer for a while and we are pretty confident that the mechanical end is working fine with some adjustments made. However we need some input on how to synchronize...
Ok we got the alarm taken care of, now we are having another issue. T3 is in the spindle and when we veiw our ATC Data Page the active tool is correct (003) next tool is (000) and actual position...
Hey guys im getting a alarm, 168 Alarm B ATC Axis condition Failure 2002. The controller is a 5020M on a Cadet 4020 mill,Can anyone give me any input on what might be going on here?
Actually when i cleaned all the crud out I must of packed some in between the blade and motor housing. Blowed everything out real good and it picked and ran correctly. Learn something everyday thanks!
Hey guys on my lb15 i noticed on the back of the spindle drive motor I have a fan, I took the screen off and cleaned everything best i could but not gettin good air flow still. Hard to see if theres...
Ok, thanks now on the control itself it does say OSP5020L on the front of it. Do you still think that its a 5000 series, Im learning on the fly so i could be wrong but i'm just reading whats on the...
Hey guys/Okuma Wiz, i've found out a couple more things since i last posted. We have a Fauc drive A06B-60440-0692 with an A20B-6044-H408 top card. The code led lite #2 is a speed deviation alarm...
No worries, the machine has been in place and doing fine for about two yrs now. We checked all electrical connections and everything seems to be good, the alarm says 110 SDU alarm 1. My problem is...
Hey guys I am having issues again with my spindle drive unit, when I press cycle start the chuck will try to start and then alarms out. The #2 code lite on the sdu is on once the alarm on, its a lb...
Yes got my % symbol in place. Really nothing has changed, no added software or updates of any kind.