[andre-dolphin]

\r\n \r\n Hello
\n
\nYou can introduce a space character after the block number macro #N
\n
\nSo where you see #N add " " (there is space character between the quotes) to read #N " "
\n
\nYou will need to do this on each lines that contains the #N in the RULES section of the post
\n
\nATb
\nandre\r\n \r\n

[HighSideNZ]

\r\n \r\n HI
\nCarrying on from this post, can you add a space between program content like the following?
\n
\nN11 G99G83X183.0Y41.0Z-14.667Q2.933R3.0F200
\n
\nmake it like
\n
\nN11 G99 G83 X183.0 Y41.0 Z-14.667 Q2.933 R3.0 F200
\n
\nThanks
\nPhil\r\n \r\n

[andre-dolphin]

\r\n \r\n Hello Phil,
\n
\nYes, you need to add an underscore character before each word ..... this is the groups section from a fanuc lathe post ....
\nGROUPS:
\n :G1 = { _G00 _G01 _G02 _G03 _G33 _G77 _G78 _G79 _G92 }
\n :G2 = { _G96 _G97 }
\n :G3 = { _G90 _G91 }
\n :G4 = { _G94 _G95 }
\n :G6 = { _G20 _G21 }
\n :G7 = { _G40 _G41 _G42 }
\n :M1 = { _M03 _M04 _M05 }
\n :M2 = { _M08 _M09 }
\n :M3 = { _M33 _M34 _M35 }
\n :M4 = { _M78 _M79 }
\nEND:
\n
\nThen use this in the MACRO and RULES sections ....... examples below
\n
\n#CRC = { [CUTCOM ? (_G40) / (_G41) / (_G42) ] }
\n
\n:GOCLW = { #N (_G02) #CRC #Y #X #I #J #F EOB }
\n
\nATb
\nAndre\r\n \r\n

[HighSideNZ]

\r\n \r\n Thanks Andre
\nWorked like a charm.
\nI feel it is much easier to read like this.
\n
\nN10 G94
\nN11 G99 G83 X183.0 Y41.0 Z-14.667 Q2.933 R3.0 F200
\nN12 G80
\nN13 M09
\nN14 G49
\nN15 T4 M06 ( Ball Nosed End Mill 10mm Dia )
\nN16 G00 G43 Z50.0 H0
\nN17 S700 M03
\nN18 G94
\nN19 X60.0 Y51.624
\nN20 Z3.0
\nN21 G01 Z-1.0 F100
\nN22 X60.0 Y30.376 F200
\nN23 X166.0 Y37.829
\nN24 X166.0 Y44.171
\nN25 X60.0 Y51.624
\nN26 X64.5 Y46.796
\n
\nCheers
\nPhil\r\n \r\n

[kenwoodhf]

I am using the post processor for EMC-2. Is there a way to put a space after the line number in the G code. It would be allot easier to read it. I have tried to change things in the file but have had no success. Thanks Jan