584,829 active members*
5,091 visitors online*
Register for free
Login Register
CNC-STEP Products

We bring precision to the point.

CNC-STEP GmbH & Co. KG
Other accessories

1050 watts milling engine 1050 FME-1 by AMB (formerly Kress 1050-FME-1)

2001 0110
Due to its continuous adjustable number of revolutions starting with 5000 rev./min., this motor can be greatly applied for all applications on Plexiglas, plastics, PVC, etc., as those materials start to melt at a number of revolutions of 10,000 rev./min. when using cheaper milling tools. This results in a milling degrade and a minimum of quality. Also the motor is extremely silent (at 5000 rev./min. only 74 dB), thus applicable in your cellar without disturbing your neighbours.
Product details Homepage Product request
CNC Handrad
CNC Handrad
Other accessory
CNC-STEP GmbH & Co. KG
Other accessories
CNC Handrad
CNC handwheel available in two connection variants. IP54 protection class. With programmable hotkeys, emergency stop and dead man's button. Translated with DeepL
Product details Homepage Product request
Kohlebürsten AMB (Kress) Fräsmotoren
Kohlebürsten AMB (Kress) Fräsmotoren
Other accessory
CNC-STEP GmbH & Co. KG
Other accessories
Replacement carbon brushes for the following of our AMB (Kress) milling motors models: 1050 FME-1, 1050 FME-1 DI, 1050 FME-P, 1050 FME-P DI, Set of 2 as the wear of the wear brushes is usually even. The set consists of 2 different carbon brushes, one with shut-off device and one without. Translated with DeepL
Product details Homepage Product request
Kohlebürsten Suhner Fräsmotoren
Kohlebürsten UAL 23-RF
Other accessory
CNC-STEP GmbH & Co. KG
Other accessories
Kohlebürsten Suhner Fräsmotoren
Replacement carbon brushes for our Suhner milling motors models UAD 30-RF, UAK 30-RF or UAL 23-RF. Set of 2 as the wear of the carbon brushes is usually even. Translated with DeepL
Product details Homepage Product request
1050 watts milling engine by Kress 1050-FME
1050 watts milling engine by Kress 1050-FME
Other accessory
CNC-STEP GmbH & Co. KG
Other accessories
211110
Product characteristics: MAXX-Power engine 1050 watts Slimmest design for best ergonomics Solid shaft electronic control for constand achievement and number of revolutions Gentle approach and current surge limitation Armared coil of the engine vagainst dust and particle infestation Steel engine flange with double stocking for higher milling forces Spindle lock for easy changig of the milling tools Electronic overload protection prevebts an overheating of the engine Switching off carbon brush condustors for the protection of the engine To the drive suitably by bending waves Mains cable with patent Quick catch and 4m rubber inlet. In the lengths of 4 and 6 meters as accessories available.
Product details Homepage Product request
Industrial - Milling Motor / Milling Spindle SUHNER 3.500 - 30.000 r/min
Industrial - Milling Motor / Milling Spindle SUHNER 3.500 - 30.000 r/min
Milling motor for cnc router
CNC-STEP GmbH & Co. KG
Other accessories
Milling motor for cnc router
Product details Homepage Product request
IP65 Radio controlled USB keypad / Wireless CNC remote
IP65 Radio controlled USB keypad / Wireless CNC remote
Other accessory
CNC-STEP GmbH & Co. KG
Other accessories
Wireless USB keyboard/ Handwheel for operating CNC machines via WinPC NC or for example Mach3 The remote control is made to use all cnc controlled machines, which are driven with different versions of WinPC NC CAM software from Lewetz, in your basic functions via radio. Our wireless remote control works with any CAM software which customizes the key assignment via hotkeys. Annoying dragging around a regular PC keyboard is abolished in the main work with the CNC machine. In addition, the dust-and splash-proof IP65 housing of the keypad is made of rugged plastic, shock resistant and provided with an additional round rubber bumper edge. Thus, you operate your machine in a very simple and practical way for example when starting from zero points on workpieces as in contrast to an operation on a conventional keyboard .
  • Wireless Keypad CNC-STEP
  • Back view wireless keypad
  • Keypad
Product details Homepage Product request
Kress collet 2.35 mm
Kress collet 2.35 mm
Other accessory
CNC-STEP GmbH & Co. KG
Other accessories
Kress collet 2.35 mm
for Proxxon or Dremel cutters etc.
Product details Homepage Product request
Minimum quantity lubrication system
Minimum quantity lubrication system
Other accessory
CNC-STEP GmbH & Co. KG
Other accessories
3005 0001
The appropriate minimal quantity lubrication system, which is fastened with a fixing screw will fit all CNC milling machines. It can be operated with eg a small compressor, where a minimal air pressure of 2 bar is necessary. Fine tuning of amount and air pressure can be adjusted via nozzle as well as switch. All tubing is made of stainless steel and therefore resistant to corrosion. The suction side is equipped with a filter. If extensions are needed, ordinary plastic tubing or appropriate high pressure tubing can be used. An ordinary ‘biker drinking flask’ is sufficient to use as a vessel. The minimal quantity lubrication system will be used most when dealing with soft materials which are difficult to mill, such as aluminium in pure form or copper. These materials can not dispense a minimal lubricating system!
  • Min. quantity lubrication
Product details Homepage Product request
Spannzangensatz für Kress Fräsmotoren
Spannzangensatz für Kress Fräsmotoren
Other accessory
CNC-STEP GmbH & Co. KG
Other accessories
he set of 3 high quality collets from Germany enjoys a high concentricity and high quality materials! The collet set consists of 3 clamps with diameters of 3mm, 6mm and 1/8 inch. With these diameters and the standard delivered with the motor 8mm collet you are ready for the most milling and engraving tools. Product Features: Collet set 3 pieces Fits all Kress spindles High-quality original German quality, incomparable with many China-imports! Diameter 3mm, 6mm, 1/8 ", optional 2.35, 4mm and 1/4" stock Concentricity 0.004 mm Quality spring steel
  • Collet kit 3 piece
  • Collet kit 3 piece
  • Collet kit 3 piece
  • Collet kit 3 piece
Product details Homepage Product request
Tangential knife EOT-3
Tangential knife EOT-3
Other accessory
CNC-STEP GmbH & Co. KG
Other accessories
Tangential knife EOT-3
12 Volt
12 bis 24 Volt
circa 3500 bis 7000 Hübe per Minute
Eurohals (43 mm)
circa 86 mm x 58 mm x 220 mm
The oscillating tangential knife EOT-3 from our assortment is ideal for cutting in materials such as cork, leather, rubber, hard foam, cardboard and many more. The robust housing and the high-quality components make this cutting module precise in machining and guarantees a long service life. Due to the standardized euro-neck mounting bracket and the plug connection the installation is quick and simple.
  • Tangential knife EOT-3
  • Tangential knife EOT-3
  • Tangential knife EOT-3
  • Tangential knife EOT-3
Product details Homepage Product request
Tool changing system for CNC machines
Tool changing system for CNC machines
Other accessory
CNC-STEP GmbH & Co. KG
Other accessories
HSK E25
extension spring
Double-acting pneumatic cylinder, maintenance-free, min. 4 bar
350 x 120 x 80 mm
approx. 3.2 kg
aluminium
brass
spring steel
IP65 stainless steel, accuracy 0.005 mm
The change magazine with 6-fold HSK-E 25 tool holders. Due to its low weight and compact dimensions, this tool changer is ideal not only for larger, but also for small CNC portal milling machines. The changing station is designed for operation with high-frequency spindles. Upon request, we also produce changers to individual specifications, let us advise you!
Product details Homepage Product request